Side-return infill drawings for Somerset terraces — the glazed extension that fills the redundant side alley and opens up the kitchen, drawn to Somerset Council's guidance, delivered in days and revised free until your decision, with a free approval-odds check first.
Somerset Council granted 94% of the householder planning decisions it made in its latest published year — 7 points above the 87% England-wide householder average. Somerset contains Alcombe, Alvington, Ansford conservation areas (Alcombe designated 1975), so materials, fenestration and roof form are assessed against the appraisal, which is where a policy-literate drawing pack earns its keep. Its dominant Victorian (1837–1901) and postwar (1945–1970) housing stock sets the design brief on most streets.
Under Class B, a rear dormer stays permitted development up to 40m³ of added roof volume on a terrace or 50m³ on a semi-detached or detached house, while Class A allows a single-storey rear extension of 3m beyond the original rear wall on a terrace and 4m on a detached house before a full application is needed. In conservation areas such as Alcombe, Alvington and Ansford those rights are removed, so we confirm your exact address before a line is drawn. A validated householder application in Somerset is determined against an 8-week statutory target.
Alcombe (conservation area designated in 1975), Alvington (conservation area designated in 2008), Ansford (conservation area designated in 1971), Ash Priors (conservation area designated in 1993), Ashbrittle (conservation area designated in 1993), Axbridge (conservation area designated in 1991), Batcombe (conservation area designated in 1978), Bathealton (conservation area designated in 1993), Blackdown & Neroche (ward of Somerset), Blackmoor Vale (ward of Somerset), Brent (ward of Somerset), Bridgwater South (ward of Somerset), Bridgwater West (ward of Somerset), Brympton (ward of Somerset), Burnham on Sea North (ward of Somerset) and Cannington (ward of Somerset) — these are the Somerset pockets our drawings cover most. Heritage designations here include Alcombe, Alvington, Ansford, Ash Priors, Ashbrittle, Axbridge, Batcombe and Bathealton. Somerset Council weighs each proposal against Somerset Council's development plan and the design policies it applies to householder applications, where the 177,300 homes here are 19% pre-1900, 6% 1973-1982, 6% 1965-1972, which is what sets the realistic roof and rear-projection options. On roofs the borough is steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and shallow trussed roofs typical of 1970s building, over Victorian and earlier houses (19% of 177,300 homes), 1970s and early-1980s houses (6%) and late-1960s and early-1970s houses (6%).
Somerset's designated heritage is specific, and it is the first thing we check against your address: Alcombe (conservation area designated in 1975), Alvington (conservation area designated in 2008), Ansford (conservation area designated in 1971), Ash Priors (conservation area designated in 1993), Ashbrittle (conservation area designated in 1993), Axbridge (conservation area designated in 1991), Batcombe (conservation area designated in 1978) and Bathealton (conservation area designated in 1993). Inside those boundaries permitted development is curtailed and Somerset Council assesses materials, window detail and roof form against the area's own appraisal, so a scheme that would be waved through two streets away can need a full application here.
Beyond the designated areas, Somerset takes in Blackdown & Neroche, Blackmoor Vale, Brent, Bridgwater South, Bridgwater West, Brympton, Burnham on Sea North and Cannington. No Article 4 direction is recorded for Somerset Council, but the district's 8 conservation areas still limit permitted development on those streets.
On stock, Somerset is Victorian and earlier houses (19% of 177,300 homes), 1970s and early-1980s houses (6%) and late-1960s and early-1970s houses (6%) — which is why steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and shallow trussed roofs typical of 1970s building govern what a loft or rear projection can realistically be. Somerset Council decided 1,422 householder applications in the latest published year and granted 94%, with 74% issued inside the eight-week target. Those are the numbers our drawings are prepared against.
The full build-period split for Somerset runs pre-1900 3% (190 homes), 1900-1918 0% (30 homes), 1919-1929 0% (10 homes), 1930-1939 6% (350 homes), 1945-1954 3% (170 homes), 1955-1964 30% (1,850 homes), 1965-1972 33% (1,990 homes), 1973-1982 4% (260 homes), 1983-1992 5% (310 homes), 1993-1999 4% (220 homes) and 2000-2008 3% (170 homes). That distribution is why pre-1900 detailing dominates the drawings here, and it is measured from council-tax records rather than assumed from the street name.
Somerset Council also decides for Blackdown & Neroche, Blackmoor Vale, Brent, Bridgwater South, Bridgwater West, Brympton, Burnham on Sea North and Cannington, so a decision in Somerset sits inside a wider pattern of decisions we track across the same authority — useful when an officer cites a precedent from the next area over.
Published figures for Somerset and Somerset Council. These are the numbers that decide what is realistic on your street, so we work from them rather than from national averages.
| Measure | Somerset |
|---|---|
| Dwellings recorded | 177,300 |
| Built pre-1900 | 190 (3%) |
| Built 1900-1918 | 30 (0%) |
| Built 1919-1929 | 10 (0%) |
| Built 1930-1939 | 350 (6%) |
| Built 1945-1954 | 170 (3%) |
| Built 1955-1964 | 1,850 (30%) |
| Built 1965-1972 | 1,990 (33%) |
| Built 1973-1982 | 260 (4%) |
| Built 1983-1992 | 310 (5%) |
| Built 1993-1999 | 220 (4%) |
| Built 2000-2008 | 170 (3%) |
| Built before 1919 | 22% |
| Built 1919–1939 | 8% |
| Built 1945–2008 | 56% |
| Conservation areas in Somerset | 8 (Alcombe, Alvington…) |
| Conservation areas district-wide | 178 |
| Article 4 directions recorded | 0 |
| Householder applications decided | 1,422 |
| Householder applications granted | 94% |
| Decided within 8 weeks | 74% |
Dwelling stock from VOA council-tax data at 31 March 2025; conservation-area and Article 4 counts from planning.data.gov.uk (MHCLG); decision figures are Somerset Council's own, from MHCLG live table PS2 for the year to 31 March 2026.
The side return is the classic terrace fix, and Somerset has the stock for it — the borough is built largely from Victorian and earlier houses (19% of 177,300 homes), 1970s and early-1980s houses (6%) and late-1960s and early-1970s houses (6%), and the Victorian and Edwardian versions almost all have an L-shaped back addition with a wasted alley beside it. Fill that alley and the dark galley kitchen becomes a bright, square room the full width of the house. Somerset Council judges the infill against Somerset Council's development plan and the design policies it applies to householder applications, and because it runs along the party boundary, the neighbour relationship is read before the design.
That boundary is where the drawings earn their keep. We set the infill wall on or up to the line, keep the roof — usually a glazed lantern or a shallow pitch tying into the existing back-addition slope — below the neighbour's first-floor windows, and detail the rainwater and party-wall junction so the build is watertight and the Party Wall Act is satisfied. Somerset contains Alcombe, Alvington, Ansford conservation areas (Alcombe designated 1975), so materials, fenestration and roof form are assessed against the appraisal, so we resolve it on the section rather than leave it to the case officer.
Many of Somerset's terraces sit in conservation areas — Alcombe, Alvington, Ansford, Ash Priors, Ashbrittle, Axbridge, Batcombe and Bathealton among them — where a side extension is no longer permitted development. No Article 4 direction is recorded for Somerset Council, but the district's 8 conservation areas still limit permitted development on those streets. We confirm the designation before a line is drawn.
Some single-storey side returns in Somerset are permitted development, but the width and boundary make an application more likely than for a straight rear extension. You will normally need to apply to Somerset Council if any of these apply:
We draw the infill wall on the boundary, the glazed roof below the neighbour's windows and the party-wall junction on the page — the details Somerset Council's officers and your neighbour both check — and submit a validation-complete pack, whether that is a lawful development certificate or a full householder application.
Below is Somerset Council's real householder decision record, drawn from official planning statistics and refreshed as new data lands. Somerset Council granted 94% of 1,422 householder decisions in the year to 31 March 2026, 74% of them inside eight weeks. Side returns hinge on width, roof glazing and the party boundary, so a pack that resolves those details upfront is decided faster and refused less often than a DIY submission.
Source: MHCLG planning application statistics (householder decisions, England, 1 April 2025 - 31 March 2026). Compare every borough on our London approval-rate league table.
Tell us about your project and get a fixed, no-obligation quote back within one working day. If you don't need planning permission at all, we'll tell you that too — for free.
Across Alcombe, Alvington and Ansford, the approved side return is a single-storey infill roofed with a glazed lantern or roof light to pull daylight deep into the plan, its flank wall built on the boundary and finished to match the host brick. On the borough's victorian and earlier houses (19% of 177,300 homes), this is frequently the single biggest gain in usable ground-floor space, and where it stays within the width and height limits it can proceed under permitted development or a lawful development certificate.
The 177,300 homes here are 19% pre-1900, 6% 1973-1982, 6% 1965-1972, which is what sets the realistic roof and rear-projection options. We keep the glazed roof below the neighbour's cill line, set the gutter and the party-wall flashing so water and maintenance are designed in, and — where owners want the full open-plan room — pair the infill with a rear extension as a single wraparound application. That way Somerset Council sees one coherent scheme rather than two overlapping ones.
We draw side-return infills on every terraced street in the borough. A few of the neighbourhoods where Somerset side returns come up most often:
Side return extension drawings for Alcombe's conservation area designated in 1975 — width-checked, party-wall detailed and drawn to Somerset Council's guidance.
Side return extension drawings for Alvington's conservation area designated in 2008 — width-checked, party-wall detailed and drawn to Somerset Council's guidance.
Side return extension drawings for Ansford's conservation area designated in 1971 — width-checked, party-wall detailed and drawn to Somerset Council's guidance.
Side return extension drawings for Ash Priors's conservation area designated in 1993 — width-checked, party-wall detailed and drawn to Somerset Council's guidance.
Side return extension drawings for Ashbrittle's conservation area designated in 1993 — width-checked, party-wall detailed and drawn to Somerset Council's guidance.
Side return extension drawings for Axbridge's conservation area designated in 1991 — width-checked, party-wall detailed and drawn to Somerset Council's guidance.
Whether a side return in Somerset needs permission comes down to width, storeys and whether the street is designated. This is how the cases compare.
| Side return type | Permitted development? | What it gains | What Somerset Council checks |
|---|---|---|---|
| Single-storey infill, within limits | Often yes, if under half the house width | Full-width kitchen-diner | Width, 4m height, roof glazing |
| Single-storey, over half width | No — full application | Wider room, more light | Boundary treatment, neighbour amenity |
| Two-storey side return | No — full application | Room above as well as below | Bulk, overlooking, terrace rhythm |
| Wraparound (side + rear) | No — full application | L-shaped open-plan ground floor | Combined footprint, garden retained |
In conservation areas such as Alcombe and Alvington, side extensions are not permitted development and always need a full application.
A fixed process built around how Somerset Council validates and decides side-return applications — most drawings are submission-ready within seven days of survey.
Send us your Somerset postcode and terrace type. We confirm your conservation and Article 4 status, whether the infill stays within the side-extension width limit, and score your odds against live Somerset Council decisions.
We measure the side alley, the back-addition wall, floor and eaves levels and the neighbour's window heights — the numbers the width limit, roof pitch and party-wall detailing depend on.
Chartered designers develop the infill and its glazed roof to your brief, drawn inside the permitted-development limits or to Somerset Council's extension guidance, with the boundary and party-wall junction detailed.
We submit the certificate or application, manage validation and case-officer queries, and revise the drawings free until Somerset Council issues its decision.
Sometimes not. A single-storey side-return infill can be permitted development if it is no wider than half the original house, no higher than 4 metres, and the property is not on designated land. In Somerset you will need a full application to Somerset Council for anything wider or taller, for a two-storey side return, and for any side extension in a conservation area such as Alcombe and Alvington, where those rights are removed.
It is an infill that fills the narrow open alley running alongside the rear back-addition of a Victorian or Edwardian terrace — the strip of ground that is usually too small to use. Building over it squares off the ground floor, so a cramped galley kitchen becomes a full-width room. Somerset's period terraces are ideally suited to it, which is why the side return is one of the borough's most common extensions. Somerset Council is the decision-maker.
Almost always. A side return is built on or up to the boundary with your neighbour, so the Party Wall etc. Act applies and you must serve notice before work starts — this is entirely separate from Somerset Council's planning decision. We detail the party-wall junction on the drawings and flag the notice early so a surveyor can be appointed without delaying the build.
Yes, and it is common — the combined L-shape is a wraparound extension. Once the side infill joins a rear projection beyond the permitted-development depth, the whole thing needs a full householder application to Somerset Council rather than qualifying as permitted development. We draw it as one coherent scheme so the council assesses a single footprint, which reads more clearly than two overlapping proposals.
A householder planning application in Somerset runs to a statutory eight-week target, and a lawful development certificate to eight weeks as well, though an incomplete pack can stall at validation. Because a side return involves the boundary and roof glazing, a complete, well-detailed submission matters — we prepare it validation-complete and manage officer queries to keep the decision on track. Somerset Council is the decision-maker.
We price each Somerset side return individually, because alley width and roof form vary house to house, and send a fixed, no-obligation quote within one working day. It covers the full drawing pack with free revisions until Somerset Council approves, and we confirm at the outset whether your infill is permitted development or needs an application. Call 020 7864 7245 to start.
Answer five quick questions and get a free planning score for your exact address — instantly. Then, if you want the full picture, unlock the detailed analysis: your council's live approval rates, local precedents, constraints on your street and a step-by-step route to permission.
Same fixed quotes, same fast drawings — wherever your project is.