Back-of-house extension drawings for Somerset homes — the glazed kitchen-diner across the rear, drawn to Somerset Council's depth and daylight limits, delivered in days and revised free until your decision, with a free approval-odds check first.
Somerset Council granted 94% of the householder planning decisions it made in its latest published year — 7 points above the 87% England-wide householder average. Somerset contains Alcombe, Alvington, Ansford conservation areas (Alcombe designated 1975), so materials, fenestration and roof form are assessed against the appraisal, which is where a policy-literate drawing pack earns its keep. Its dominant Victorian (1837–1901) and postwar (1945–1970) housing stock sets the design brief on most streets.
Under Class B, a rear dormer stays permitted development up to 40m³ of added roof volume on a terrace or 50m³ on a semi-detached or detached house, while Class A allows a single-storey rear extension of 3m beyond the original rear wall on a terrace and 4m on a detached house before a full application is needed. In conservation areas such as Alcombe, Alvington and Ansford those rights are removed, so we confirm your exact address before a line is drawn. A validated householder application in Somerset is determined against an 8-week statutory target.
Alcombe (conservation area designated in 1975), Alvington (conservation area designated in 2008), Ansford (conservation area designated in 1971), Ash Priors (conservation area designated in 1993), Ashbrittle (conservation area designated in 1993), Axbridge (conservation area designated in 1991), Batcombe (conservation area designated in 1978), Bathealton (conservation area designated in 1993), Blackdown & Neroche (ward of Somerset), Blackmoor Vale (ward of Somerset), Brent (ward of Somerset), Bridgwater South (ward of Somerset), Bridgwater West (ward of Somerset), Brympton (ward of Somerset), Burnham on Sea North (ward of Somerset) and Cannington (ward of Somerset) — these are the Somerset pockets our drawings cover most. Heritage designations here include Alcombe, Alvington, Ansford, Ash Priors, Ashbrittle, Axbridge, Batcombe and Bathealton. Somerset Council weighs each proposal against Somerset Council's development plan and the design policies it applies to householder applications, where the 177,300 homes here are 19% pre-1900, 6% 1973-1982, 6% 1965-1972, which is what sets the realistic roof and rear-projection options. On roofs the borough is steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and shallow trussed roofs typical of 1970s building, over Victorian and earlier houses (19% of 177,300 homes), 1970s and early-1980s houses (6%) and late-1960s and early-1970s houses (6%).
Somerset's designated heritage is specific, and it is the first thing we check against your address: Alcombe (conservation area designated in 1975), Alvington (conservation area designated in 2008), Ansford (conservation area designated in 1971), Ash Priors (conservation area designated in 1993), Ashbrittle (conservation area designated in 1993), Axbridge (conservation area designated in 1991), Batcombe (conservation area designated in 1978) and Bathealton (conservation area designated in 1993). Inside those boundaries permitted development is curtailed and Somerset Council assesses materials, window detail and roof form against the area's own appraisal, so a scheme that would be waved through two streets away can need a full application here.
Beyond the designated areas, Somerset takes in Blackdown & Neroche, Blackmoor Vale, Brent, Bridgwater South, Bridgwater West, Brympton, Burnham on Sea North and Cannington. No Article 4 direction is recorded for Somerset Council, but the district's 8 conservation areas still limit permitted development on those streets.
On stock, Somerset is Victorian and earlier houses (19% of 177,300 homes), 1970s and early-1980s houses (6%) and late-1960s and early-1970s houses (6%) — which is why steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and shallow trussed roofs typical of 1970s building govern what a loft or rear projection can realistically be. Somerset Council decided 1,422 householder applications in the latest published year and granted 94%, with 74% issued inside the eight-week target. Those are the numbers our drawings are prepared against.
The full build-period split for Somerset runs pre-1900 3% (190 homes), 1900-1918 0% (30 homes), 1919-1929 0% (10 homes), 1930-1939 6% (350 homes), 1945-1954 3% (170 homes), 1955-1964 30% (1,850 homes), 1965-1972 33% (1,990 homes), 1973-1982 4% (260 homes), 1983-1992 5% (310 homes), 1993-1999 4% (220 homes) and 2000-2008 3% (170 homes). That distribution is why pre-1900 detailing dominates the drawings here, and it is measured from council-tax records rather than assumed from the street name.
Somerset Council also decides for Blackdown & Neroche, Blackmoor Vale, Brent, Bridgwater South, Bridgwater West, Brympton, Burnham on Sea North and Cannington, so a decision in Somerset sits inside a wider pattern of decisions we track across the same authority — useful when an officer cites a precedent from the next area over.
Published figures for Somerset and Somerset Council. These are the numbers that decide what is realistic on your street, so we work from them rather than from national averages.
| Measure | Somerset |
|---|---|
| Dwellings recorded | 177,300 |
| Built pre-1900 | 190 (3%) |
| Built 1900-1918 | 30 (0%) |
| Built 1919-1929 | 10 (0%) |
| Built 1930-1939 | 350 (6%) |
| Built 1945-1954 | 170 (3%) |
| Built 1955-1964 | 1,850 (30%) |
| Built 1965-1972 | 1,990 (33%) |
| Built 1973-1982 | 260 (4%) |
| Built 1983-1992 | 310 (5%) |
| Built 1993-1999 | 220 (4%) |
| Built 2000-2008 | 170 (3%) |
| Built before 1919 | 22% |
| Built 1919–1939 | 8% |
| Built 1945–2008 | 56% |
| Conservation areas in Somerset | 8 (Alcombe, Alvington…) |
| Conservation areas district-wide | 178 |
| Article 4 directions recorded | 0 |
| Householder applications decided | 1,422 |
| Householder applications granted | 94% |
| Decided within 8 weeks | 74% |
Dwelling stock from VOA council-tax data at 31 March 2025; conservation-area and Article 4 counts from planning.data.gov.uk (MHCLG); decision figures are Somerset Council's own, from MHCLG live table PS2 for the year to 31 March 2026.
The rear extension is the workhorse of Somerset home improvement — it is how a dark back kitchen becomes an open family room facing the garden. Because the borough is built largely from Victorian and earlier houses (19% of 177,300 homes), 1970s and early-1980s houses (6%) and late-1960s and early-1970s houses (6%), most back walls sit close to a neighbour on at least one side, and that proximity, not the design, is what Somerset Council scrutinises. The council reads the proposal against Somerset Council's development plan and the design policies it applies to householder applications, and the first line an officer draws is the 45-degree splay from the neighbour's nearest window.
So the drawings live or die on geometry. We set the depth against the exact permitted-development figure, hold the eaves and the flat-roof or lantern build-up under the 4-metre height ceiling, and show the projection tested against both the 45-degree plan angle and the 25-degree section angle to the neighbouring windows. Somerset contains Alcombe, Alvington, Ansford conservation areas (Alcombe designated 1975), so materials, fenestration and roof form are assessed against the appraisal, so the rear elevation is composed around it rather than corrected after an objection.
Where the property sits in a conservation area — Alcombe, Alvington, Ansford, Ash Priors, Ashbrittle, Axbridge, Batcombe and Bathealton among Somerset's — the larger-home extension route is switched off and even a modest rear addition needs consent. No Article 4 direction is recorded for Somerset Council, but the district's 8 conservation areas still limit permitted development on those streets. We confirm the designation before the survey.
Many single-storey rear extensions in Somerset are permitted development and need no application. You will normally need to apply to Somerset Council, or use the larger-home prior-approval route, if any of these apply:
We draw the depth, the roof build-up and the daylight splays to each neighbour on the page — the tests Somerset Council's officers apply first — and submit a validation-complete pack, whether that is a lawful development certificate, a larger-home prior-approval notice or a full householder application.
Below is Somerset Council's real householder decision record, taken from official planning statistics and refreshed as new data lands. Somerset Council granted 94% of 1,422 householder decisions in the year to 31 March 2026, 74% of them inside eight weeks. Rear extensions turn most often on neighbour daylight and depth, so a drawing pack that proves those tests upfront is decided faster and refused less often than a DIY submission.
Source: MHCLG planning application statistics (householder decisions, England, 1 April 2025 - 31 March 2026). Compare every borough on our London approval-rate league table.
Tell us about your project and get a fixed, no-obligation quote back within one working day. If you don't need planning permission at all, we'll tell you that too — for free.
Across Alcombe, Alvington and Ansford, the approved rear extension is typically a single-storey glazed box within the depth limit, roofed either flat with a lantern or in a shallow mono-pitch, and finished in brick or render to match the host wall. On the borough's victorian and earlier houses (19% of 177,300 homes), keeping the projection to the permitted-development figure often avoids an application entirely; where owners want the full 6 metres, the larger-home route succeeds when the neighbour-consultation period passes without a sustained objection.
The 177,300 homes here are 19% pre-1900, 6% 1973-1982, 6% 1965-1972, which is what sets the realistic roof and rear-projection options. We keep the extension inside the daylight splays, set any glazed roof below the first-floor cill, and retain the garden depth Somerset Council expects — so the back elevation answers the amenity case before a neighbour can lodge one. Two-storey rear extensions we draw with the 7-metre boundary gap and privacy screening resolved on the plan.
We draw rear extensions on every street in the borough. A few of the neighbourhoods where Somerset back-of-house projects come up most often:
Rear extension drawings for Alcombe's conservation area designated in 1975 — depth-checked, daylight-tested and drawn to Somerset Council's guidance.
Rear extension drawings for Alvington's conservation area designated in 2008 — depth-checked, daylight-tested and drawn to Somerset Council's guidance.
Rear extension drawings for Ansford's conservation area designated in 1971 — depth-checked, daylight-tested and drawn to Somerset Council's guidance.
Rear extension drawings for Ash Priors's conservation area designated in 1993 — depth-checked, daylight-tested and drawn to Somerset Council's guidance.
Rear extension drawings for Ashbrittle's conservation area designated in 1993 — depth-checked, daylight-tested and drawn to Somerset Council's guidance.
Rear extension drawings for Axbridge's conservation area designated in 1991 — depth-checked, daylight-tested and drawn to Somerset Council's guidance.
How far you can extend at the back in Somerset depends on your house type and the route you take. This is how the options compare.
| Route | Depth allowed | Consent needed | What Somerset Council checks |
|---|---|---|---|
| Standard permitted development | 3m terrace/semi · 4m detached | Lawful development certificate (optional) | Depth, 4m height, materials |
| Larger-home prior approval | 6m terrace/semi · 8m detached | Prior-approval notice + neighbour consultation | Neighbour objections on amenity |
| Full householder application | Beyond the above, or two-storey | Full planning permission | Daylight (45°/25°), bulk, garden retained |
| Conservation area | Case by case | Full planning permission | Character, roof form, boundary treatment |
The larger-home route is switched off on designated land — conservation areas such as Alcombe and Alvington and Article 4 streets need a full application.
A fixed process built around how Somerset Council validates and decides rear-extension applications — most drawings are submission-ready within seven days of survey.
Send us your Somerset postcode and house type. We confirm your conservation and Article 4 status, how much rear-extension depth you have under permitted development, and score your odds against live Somerset Council decisions.
We measure the original rear wall, floor and eaves levels, side and rear boundary distances and the neighbours' window positions — the numbers the depth limit and daylight splays depend on.
Chartered designers develop the single or two-storey rear extension to your brief, drawn inside the permitted-development limits or to Somerset Council's extension design guidance, with the daylight angles shown.
We submit the certificate, prior-approval notice or application, handle validation and case-officer queries, and revise the drawings free until Somerset Council issues its decision.
Often not. A single-storey rear extension up to 3 metres deep on a terrace or semi, or 4 metres on a detached house, and no higher than 4 metres, is usually permitted development in Somerset. You will need to involve Somerset Council for anything deeper via the larger-home route, for two-storey rear extensions, and for any rear extension in a conservation area such as Alcombe and Alvington, where those permitted-development rights fall away.
The larger-home extension scheme lets a single-storey rear extension reach 6 metres on a terrace or semi, or 8 metres on a detached house — double the standard allowance. It is not automatic: you submit a prior-approval notification to Somerset Council, neighbours are consulted, and if one objects on amenity grounds the council rules on it. It also does not apply on designated land such as Somerset's conservation areas.
It is the daylight test Somerset Council applies to protect neighbours. Drawn on plan, a line at 45 degrees from the midpoint of the neighbour's nearest ground-floor window should not be crossed by your extension; a companion 25-degree line is checked in section. If the projection breaches it, the extension is likely to be shortened or refused, so we test and prove it on the drawings before submission.
A two-storey rear extension almost always needs a full householder application to Somerset Council, as it sits outside permitted development on most homes. The council checks that it stays at least 7 metres from the rear boundary, does not overbear the neighbours and avoids new overlooking. We resolve the boundary gap, privacy and daylight on the plans so the application is decided on its merits.
Frequently, yes. If the rear extension involves work to a shared wall, building up to the boundary, or excavating foundations near a neighbour's structure, the Party Wall etc. Act applies and you must serve notice — this is separate from Somerset Council's planning decision. We flag it early and can prepare the drawings a party-wall surveyor needs alongside the planning set.
We price each Somerset rear extension on its own footprint and send a fixed, no-obligation quote within one working day. It covers the full drawing pack with free revisions until Somerset Council approves, and we confirm at the outset whether your extension is permitted development, needs prior approval, or a full application. Call 020 7864 7245 to begin.
Answer five quick questions and get a free planning score for your exact address — instantly. Then, if you want the full picture, unlock the detailed analysis: your council's live approval rates, local precedents, constraints on your street and a step-by-step route to permission.
Same fixed quotes, same fast drawings — wherever your project is.