Hip-to-gable drawings for Stour & Allen Vale semis and end-terraces — building the sloping hipped end up into a flat gable wall to unlock the full width of the roof, drawn to Dorset Council's guidance, delivered in days and revised free until your decision, with a free approval-odds check first.
Dorset Council granted 95% of the householder planning decisions it made in its latest published year — 8 points above the 87% England-wide householder average. Stour & Allen Vale contains Almer Conservation Area, Hinton Martell Conservation Area, Horton Conservation Area conservation areas (Almer Conservation Area designated 1992), so materials, fenestration and roof form are assessed against the appraisal, which is where a policy-literate drawing pack earns its keep. Its dominant Victorian (1837–1901) and postwar (1945–1970) housing stock sets the design brief on most streets.
Before permission is required, Class B allows 40m³ of added loft volume on a terrace and 50m³ on a semi or detached house, and Class A allows a 3m single-storey rear extension on a terrace or 4m on a detached house. Stour & Allen Vale carries at least one Article 4 direction, and conservation areas including Almer Conservation Area, Hinton Martell Conservation Area and Horton Conservation Area remove those rights outright, so we confirm your exact address before a line is drawn. A validated householder application in Stour & Allen Vale is determined against an 8-week statutory target.
Almer (conservation area designated in 1992), Hinton Martell (conservation area designated in 1978), Horton (conservation area designated in 1990), Mapperton (conservation area designated in 1992), Pamphill (conservation area designated in 1987), Shapwick (conservation area designated in 1978), Sturminster Marshall (conservation area designated in 1987), Shapwick (civil parish within Stour & Allen Vale), Sturminster Marshall (civil parish within Stour & Allen Vale), Chalbury (civil parish within Stour & Allen Vale), Horton (civil parish within Stour & Allen Vale), Hinton (civil parish within Stour & Allen Vale) and Holt (civil parish within Stour & Allen Vale) — these are the Stour & Allen Vale pockets our drawings cover most. Heritage designations here include Almer Conservation Area, Hinton Martell Conservation Area, Horton Conservation Area, Mapperton Conservation Area, Pamphill Conservation Area, Shapwick Conservation Area and Sturminster Marshall Conservation Area. Dorset Council weighs each proposal against Dorset Council's adopted local plan and its householder design guidance, where the 2,110 homes here are 24% pre-1900, 9% 1945-1954, 8% 1955-1964, which is what sets the realistic roof and rear-projection options. On roofs the borough is steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and simple gabled and hipped roofs typical of early postwar building, over Victorian and earlier houses (24% of 2,110 homes), early postwar houses (9%) and late-1950s and early-1960s houses (8%).
What is permitted in Stour & Allen Vale turns on designation first, so that is where we start: Almer (conservation area designated in 1992), Hinton Martell (conservation area designated in 1978), Horton (conservation area designated in 1990), Mapperton (conservation area designated in 1992), Pamphill (conservation area designated in 1987), Shapwick (conservation area designated in 1978) and Sturminster Marshall (conservation area designated in 1987). Inside those boundaries permitted development is curtailed and Dorset Council assesses materials, window detail and roof form against the area's own appraisal, so a scheme that would be waved through two streets away can need a full application here.
Beyond the designated areas, Stour & Allen Vale takes in Shapwick, Sturminster Marshall, Chalbury, Horton, Hinton and Holt. Dorset Council has 77 recorded Article 4 directions — check the address before assuming PD applies in Stour & Allen Vale.
On stock, Stour & Allen Vale is Victorian and earlier houses (24% of 2,110 homes), early postwar houses (9%) and late-1950s and early-1960s houses (8%) — which is why steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and simple gabled and hipped roofs typical of early postwar building govern what a loft or rear projection can realistically be. Dorset Council decided 1,261 householder applications in the latest published year and granted 95%, with 78% issued inside the eight-week target. We draw to that record rather than to a national average.
The full build-period split for Stour & Allen Vale runs pre-1900 24% (510 homes), 1900-1918 3% (70 homes), 1919-1929 2% (50 homes), 1930-1939 5% (110 homes), 1945-1954 9% (180 homes), 1955-1964 8% (170 homes), 1965-1972 6% (120 homes), 1973-1982 7% (150 homes), 1983-1992 8% (170 homes), 1993-1999 8% (170 homes) and 2000-2008 5% (100 homes). That distribution is why pre-1900 detailing dominates the drawings here, and it is measured from council-tax records rather than assumed from the street name.
Dorset Council also decides for Beacon, Beaminster, Blackmore Vale, Blandford, Chalk Valleys, Charminster St Mary's, Chickerell and Cranborne & Alderholt, so a decision in Stour & Allen Vale sits inside a wider pattern of decisions we track across the same authority — useful when an officer cites a precedent from the next area over.
The Article 4 directions recorded for this council include 1-3 The Lane, Kingston, Corfe Castle, 10 Cornwall Road, Swanage, 6 Burlington Road, Swanage and Avon Castle & Matchams Park Estate. Each removes a specific permitted-development right inside its own boundary, which is why the check is done on the address rather than on the town.
Published figures for Stour & Allen Vale and Dorset Council. These are the numbers that decide what is realistic on your street, so we work from them rather than from national averages.
| Measure | Stour & Allen Vale |
|---|---|
| Dwellings recorded | 2,110 |
| Built pre-1900 | 510 (24%) |
| Built 1900-1918 | 70 (3%) |
| Built 1919-1929 | 50 (2%) |
| Built 1930-1939 | 110 (5%) |
| Built 1945-1954 | 180 (9%) |
| Built 1955-1964 | 170 (8%) |
| Built 1965-1972 | 120 (6%) |
| Built 1973-1982 | 150 (7%) |
| Built 1983-1992 | 170 (8%) |
| Built 1993-1999 | 170 (8%) |
| Built 2000-2008 | 100 (5%) |
| Built before 1919 | 27% |
| Built 1919–1939 | 8% |
| Built 1945–2008 | 50% |
| Conservation areas in Stour & Allen Vale | 7 (Almer Conservation Area, Hinton Martell Conservation Area…) |
| Conservation areas district-wide | 311 |
| Article 4 directions recorded | 77 |
| Householder applications decided | 1,261 |
| Householder applications granted | 95% |
| Decided within 8 weeks | 78% |
Dwelling stock from VOA council-tax data at 31 March 2025; conservation-area and Article 4 counts from planning.data.gov.uk (MHCLG); decision figures are Dorset Council's own, from MHCLG live table PS2 for the year to 31 March 2026.
The hip-to-gable is the semi's loft, and Stour & Allen Vale has the stock that needs it — the borough runs to Victorian and earlier houses (24% of 2,110 homes), early postwar houses (9%) and late-1950s and early-1960s houses (8%), and wherever the roof is hipped it wastes the triangle of space where the slope cuts in at the side. Build that hip up into a gable wall and the loft gains full-height room right across the width, usually with a rear dormer behind it. Dorset Council judges the scheme against Dorset Council's adopted local plan and its householder design guidance, and because the gable is a side elevation it is read against the neighbouring house first.
That neighbour relationship is the drawing's job. We build the gable to the original ridge line, match the brick or render and the verge detail to the host, and where the house is one of a mirrored pair we show the new gable against the neighbour's retained hip so the officer can weigh the balance. Stour & Allen Vale contains Almer Conservation Area, Hinton Martell Conservation Area, Horton Conservation Area conservation areas (Almer Conservation Area designated 1992), so materials, fenestration and roof form are assessed against the appraisal, and on a paired roof that is precisely the test a hip-to-gable has to pass.
Where Stour & Allen Vale's streets are designated — Almer Conservation Area, Hinton Martell Conservation Area, Horton Conservation Area, Mapperton Conservation Area, Pamphill Conservation Area, Shapwick Conservation Area and Sturminster Marshall Conservation Area among them — a hip-to-gable is scrutinised hard, because losing a hip changes the roofscape the area is protected for. Dorset Council has 77 recorded Article 4 directions — check the address before assuming PD applies in Stour & Allen Vale. We check the designation before the gable is drawn.
A hip-to-gable in Stour & Allen Vale is not permitted development — extending the roof up and out over the hip takes it past what Class B allows — so it needs a full application to Dorset Council. These are the points the council weighs:
We draw the new gable to the existing ridge, the verge and materials matched to the host, and the balance with the neighbour's retained hip — the side-elevation relationships Dorset Council's officers check first — and submit a validation-complete householder application, usually with the rear dormer on the same drawings.
Below is Dorset Council's real householder decision record, drawn from official planning statistics and refreshed as new data lands. Dorset Council granted 95% of its householder applications in the year to 31 March 2026, and Almer Conservation Area shapes what is approved here. A hip-to-gable turns on side-elevation bulk and the balance of the pair, so a pack that draws the gable against the neighbour is decided faster and refused less often than a DIY submission.
Source: MHCLG planning application statistics (householder decisions, England, 1 April 2025 - 31 March 2026). Compare every borough on our London approval-rate league table.
Tell us about your project and get a fixed, no-obligation quote back within one working day. If you don't need planning permission at all, we'll tell you that too — for free.
Across Almer, Hinton Martell and Horton, the hip-to-gable that goes through is the restrained one: the gable built to the original ridge rather than above it, materials matched so the extended end reads as part of the house, and — on a pair — the new wall sitting comfortably beside the neighbour's hip rather than overwhelming it. On the borough's victorian and earlier houses (24% of 2,110 homes), squaring one or both hips is what makes the whole loft usable, which is why it is nearly always drawn with a rear dormer behind.
The 2,110 homes here are 24% pre-1900, 9% 1945-1954, 8% 1955-1964, which is what sets the realistic roof and rear-projection options. We hold the gable to the ridge, detail the verge and the flank window to sit quietly, and present the gable and dormer as one roof alteration — so Dorset Council assesses a single coherent change to the roof rather than two competing ones.
We draw hip-to-gable lofts on the semi-detached and end-of-terrace streets across the borough. A few of the neighbourhoods where Stour & Allen Vale hip-to-gables come up most often:
Hip-to-gable loft drawings for Almer's conservation area designated in 1992 — ridge-matched, pair-balanced and drawn to Dorset Council's guidance.
Hip-to-gable loft drawings for Hinton Martell's conservation area designated in 1978 — ridge-matched, pair-balanced and drawn to Dorset Council's guidance.
Hip-to-gable loft drawings for Horton's conservation area designated in 1990 — ridge-matched, pair-balanced and drawn to Dorset Council's guidance.
Hip-to-gable loft drawings for Mapperton's conservation area designated in 1992 — ridge-matched, pair-balanced and drawn to Dorset Council's guidance.
Hip-to-gable loft drawings for Pamphill's conservation area designated in 1987 — ridge-matched, pair-balanced and drawn to Dorset Council's guidance.
Hip-to-gable loft drawings for Shapwick's conservation area designated in 1978 — ridge-matched, pair-balanced and drawn to Dorset Council's guidance.
A hip-to-gable only applies where the roof is hipped — and what it gains depends on the house. This is how the cases compare.
| Roof / house type | Hip-to-gable route | What it gains | What Dorset Council checks |
|---|---|---|---|
| Hipped semi-detached | Full application, one gable | Full-width loft on the hipped side | Balance with the paired neighbour |
| Hipped end-terrace | Full application, one gable | Squares off the exposed end | Side elevation and street rhythm |
| Hipped detached | Full application, one or both ends | Loft across the whole roof | Bulk and the wider roofscape |
| Already gabled roof | Not needed — dormer only | Space via a rear dormer instead | Dormer volume and set-back |
In conservation areas such as Almer Conservation Area and Hinton Martell Conservation Area, the loss of a hip is resisted and a hip-to-gable is assessed on its effect on the protected roofscape.
A fixed process built around how Dorset Council validates and decides hip-to-gable applications — most drawings are submission-ready within seven days of survey.
Send us your Stour & Allen Vale postcode and whether your roof is hipped one or both ends. We confirm your conservation and Article 4 status and score your odds against live Dorset Council decisions.
We measure the ridge and eaves, the hip geometry and — on a pair — the neighbour's roof, so the new gable can be drawn to the original ridge and balanced against the adjoining house.
Chartered designers develop the gable and its rear dormer to your brief, drawn to Dorset Council's roof-alteration guidance with the side elevation and neighbour relationship resolved on the page.
We submit the householder application, manage validation and case-officer queries, and revise the drawings free until Dorset Council issues its decision.
Yes. A hip-to-gable rebuilds the sloping hipped end of the roof as a vertical gable, and because that extends the roof it falls outside permitted development — so it always needs a full householder application to Dorset Council, whether or not your street is designated. It is usually submitted together with a rear dormer as a single roof-alteration application. This applies to your Stour & Allen Vale address specifically.
It replaces the roof's sloping hipped end with a flat gable wall built up to the ridge, turning the wasted triangle where the slope cuts in into full-height loft space across the width of the house. Stour & Allen Vale's hipped semis and end-terraces suit it especially well, and it is nearly always paired with a rear dormer to open up the back of the roof too. Dorset Council is the decision-maker.
Yes, and a matching pair often reads better to Dorset Council than a single gable on one side, because it keeps the two houses balanced. Where only one owner converts, we draw the new gable carefully against the neighbour's retained hip so the officer can see the pair still works. The balance of the pair is one of the main things the council weighs. This applies to your Stour & Allen Vale address specifically.
Almost always. The gable opens up the side of the roof and a rear dormer opens up the back, and together they make the whole loft usable — so in Stour & Allen Vale the two are typically drawn and submitted as one application to Dorset Council. Presenting them together means the council assesses a single coherent change to the roof rather than two separate alterations.
Usually, on a semi or end-terrace. The gable is built up off the flank, and the loft steelwork often bears on the party wall, so the Party Wall etc. Act applies and notice must be served before work starts — separately from Dorset Council's planning decision. We detail the junction on the drawings and flag the notice early so a surveyor can be appointed without delay. This applies to your Stour & Allen Vale address specifically.
We price each Stour & Allen Vale hip-to-gable individually, because the roof geometry and whether it is one gable or two vary house to house, and send a fixed, no-obligation quote within one working day. It covers the full drawing pack — usually gable plus rear dormer — with free revisions until Dorset Council approves. Call 020 7864 7245 to start.
Answer five quick questions and get a free planning score for your exact address — instantly. Then, if you want the full picture, unlock the detailed analysis: your council's live approval rates, local precedents, constraints on your street and a step-by-step route to permission.
Same fixed quotes, same fast drawings — wherever your project is.