Rear dormer drawings for Caldecote roofs — the box across the back slope that turns a low attic into a full-height room, drawn to South Cambridgeshire District Council's guidance and the volume limits, delivered in days and revised free until your decision, with a free approval-odds check first.
South Cambridgeshire District Council granted 95% of the householder planning decisions it made in its latest published year — 8 points above the 87% England-wide householder average. Caldecote contains Bourn, Bourn Caxton End, Caldecote conservation areas (Bourn designated 1997), so materials, fenestration and roof form are assessed against the appraisal, which is where a policy-literate drawing pack earns its keep. Its dominant postwar (1945–1970) housing stock sets the design brief on most streets.
Under Class B, a rear dormer stays permitted development up to 40m³ of added roof volume on a terrace or 50m³ on a semi-detached or detached house, while Class A allows a single-storey rear extension of 3m beyond the original rear wall on a terrace and 4m on a detached house before a full application is needed. Caldecote carries at least one Article 4 direction, and conservation areas including Bourn, Bourn Caxton End and Caldecote remove those rights outright, so we confirm your exact address before a line is drawn. A validated householder application in Caldecote is determined against an 8-week statutory target.
Bourn (conservation area designated in 1997), Bourn Caxton End (conservation area designated in 1997), Caldecote (conservation area designated in 1988), Kingston (conservation area designated in 1974), Little Gransden (conservation area designated in 2006), Kingston (civil parish within Caldecote), Little Gransden (civil parish within Caldecote), Longstowe (civil parish within Caldecote), Bourn (civil parish within Caldecote) and Childerley (civil parish within Caldecote) — these are the Caldecote pockets our drawings cover most. Heritage designations here include Bourn, Bourn Caxton End, Caldecote, Kingston and Little Gransden. South Cambridgeshire District Council weighs each proposal against South Cambridgeshire District Council's adopted local plan and its householder design guidance, where the 1,350 homes here are 32% 2000-2008, 8% 1955-1964, 7% 1973-1982, which is what sets the realistic roof and rear-projection options. On roofs the borough is trussed-rafter roofs typical of 2000s building and shallow gabled roofs typical of that period's building, over 2000s houses and apartments (32% of 1,350 homes), late-1950s and early-1960s houses (8%) and 1970s and early-1980s houses (7%).
Caldecote's designated heritage is specific, and it is the first thing we check against your address: Bourn (conservation area designated in 1997), Bourn Caxton End (conservation area designated in 1997), Caldecote (conservation area designated in 1988), Kingston (conservation area designated in 1974) and Little Gransden (conservation area designated in 2006). Inside those boundaries permitted development is curtailed and South Cambridgeshire District Council assesses materials, window detail and roof form against the area's own appraisal, so a scheme that would be waved through two streets away can need a full application here.
Beyond the designated areas, Caldecote takes in Kingston, Little Gransden, Longstowe, Bourn and Childerley. South Cambridgeshire District Council has 8 recorded Article 4 directions, removing permitted development for painting the exterior — check the address before assuming PD applies in Caldecote.
On stock, Caldecote is 2000s houses and apartments (32% of 1,350 homes), late-1950s and early-1960s houses (8%) and 1970s and early-1980s houses (7%) — which is why trussed-rafter roofs typical of 2000s building and shallow gabled roofs typical of that period's building govern what a loft or rear projection can realistically be. South Cambridgeshire District Council decided 787 householder applications in the latest published year and granted 95%, with 84% issued inside the eight-week target. Those are the numbers our drawings are prepared against.
The full build-period split for Caldecote runs pre-1900 6% (80 homes), 1900-1918 1% (10 homes), 1919-1929 1% (20 homes), 1930-1939 3% (40 homes), 1945-1954 1% (20 homes), 1955-1964 8% (110 homes), 1965-1972 4% (50 homes), 1973-1982 7% (90 homes), 1983-1992 4% (60 homes), 1993-1999 3% (40 homes) and 2000-2008 32% (430 homes). That distribution is why pre-1900 detailing dominates the drawings here, and it is measured from council-tax records rather than assumed from the street name.
South Cambridgeshire District Council also decides for Balsham, Barrington, Bassingbourn, Cottenham, Fen Ditton & Fulbourn, Foxton, Girton and Hardwick, so a decision in Caldecote sits inside a wider pattern of decisions we track across the same authority — useful when an officer cites a precedent from the next area over.
The Article 4 directions recorded for this council include Beach Road Cottenham, Clay Close Lane, Impington, Land Adjacent To Villa Road Impington and Land Opp. Milestone Farm, Great Chishill. Each removes a specific permitted-development right inside its own boundary, which is why the check is done on the address rather than on the town.
Published figures for Caldecote and South Cambridgeshire District Council. These are the numbers that decide what is realistic on your street, so we work from them rather than from national averages.
| Measure | Caldecote |
|---|---|
| Dwellings recorded | 1,350 |
| Built pre-1900 | 80 (6%) |
| Built 1900-1918 | 10 (1%) |
| Built 1919-1929 | 20 (1%) |
| Built 1930-1939 | 40 (3%) |
| Built 1945-1954 | 20 (1%) |
| Built 1955-1964 | 110 (8%) |
| Built 1965-1972 | 50 (4%) |
| Built 1973-1982 | 90 (7%) |
| Built 1983-1992 | 60 (4%) |
| Built 1993-1999 | 40 (3%) |
| Built 2000-2008 | 430 (32%) |
| Built before 1919 | 7% |
| Built 1919–1939 | 4% |
| Built 1945–2008 | 59% |
| Conservation areas in Caldecote | 5 (Bourn, Bourn Caxton End…) |
| Conservation areas district-wide | 85 |
| Article 4 directions recorded | 8 |
| Householder applications decided | 787 |
| Householder applications granted | 95% |
| Decided within 8 weeks | 84% |
Dwelling stock from VOA council-tax data at 31 March 2025; conservation-area and Article 4 counts from planning.data.gov.uk (MHCLG); decision figures are South Cambridgeshire District Council's own, from MHCLG live table PS2 for the year to 31 March 2026.
The box dormer is the workhorse loft, and most of Caldecote is built for it — the borough runs to 2000s houses and apartments (32% of 1,350 homes), late-1950s and early-1960s houses (8%) and 1970s and early-1980s houses (7%) under trussed-rafter roofs typical of 2000s building and shallow gabled roofs typical of that period's building, and a flat-roofed box across the rear slope is the cheapest cubic metre of full-height space those roofs give up. South Cambridgeshire District Council tests the dormer against South Cambridgeshire District Council's adopted local plan and its householder design guidance, and because permitted development turns on a number, the volume you propose against the volume you have left is the first thing an officer or a certificate checks.
That is why the arithmetic goes on the drawings. We calculate the box against the 40- or 50-cubic-metre allowance, count any earlier roof enlargement into the total, hold the flat roof below the ridge and set the face back off the eaves so the dormer reads as subordinate. Caldecote contains Bourn, Bourn Caxton End, Caldecote conservation areas (Bourn designated 1997), so materials, fenestration and roof form are assessed against the appraisal, so the cheeks, the window line and the material are drawn to answer it rather than invite a query.
Where Caldecote's streets are protected — Bourn, Bourn Caxton End, Caldecote, Kingston and Little Gransden among them — the Class B dormer right is switched off and even a modest rear box needs consent. South Cambridgeshire District Council has 8 recorded Article 4 directions, removing permitted development for painting the exterior — check the address before assuming PD applies in Caldecote. We confirm the designation before the box is sized.
Many rear dormers in Caldecote are permitted development, but the volume and position decide it. You will normally need a full application to South Cambridgeshire District Council if any of these apply:
We draw the box within its volume allowance, the flat roof below the ridge and the face set back off the eaves — the three things a dormer stands or falls on — and submit a validation-complete pack, whether that is a lawful development certificate or a full householder application.
Below is South Cambridgeshire District Council's real householder decision record, drawn from official planning statistics and refreshed as new data lands. South Cambridgeshire District Council granted 95% of its householder applications in the year to 31 March 2026, and Bourn shapes what is approved here. A dormer is decided on volume and set-back, so a pack that shows the calculation and the eaves detail is cleared faster and refused less often than a DIY submission.
Source: MHCLG planning application statistics (householder decisions, England, 1 April 2025 - 31 March 2026). Compare every borough on our London approval-rate league table.
Tell us about your project and get a fixed, no-obligation quote back within one working day. If you don't need planning permission at all, we'll tell you that too — for free.
Across Bourn, Bourn Caxton End and Caldecote, the dormer that goes through is the subordinate rear box: flat roof kept low, cheeks clad to recede, side windows obscure-glazed against overlooking, and the whole thing set back so the original eaves line still reads from the garden. On trussed-rafter roofs typical of 2000s building, this returns a full-height double and en-suite from what was standing-room-only, usually inside the permitted-development volume.
The 1,350 homes here are 32% 2000-2008, 8% 1955-1964, 7% 1973-1982, which is what sets the realistic roof and rear-projection options. We keep the box off the ridge, match the cheek material to the roof, and where the volume is already spent — or the street is designated — draw the dormer as a householder application composed to South Cambridgeshire District Council's roof-alteration guidance rather than push a certificate that would be refused.
We draw rear dormers on the terraced and semi-detached streets across the borough. A few of the neighbourhoods where Caldecote dormers come up most often:
Dormer loft drawings for Bourn's conservation area designated in 1997 — volume-checked, set-back-detailed and drawn to South Cambridgeshire District Council's guidance.
Dormer loft drawings for Bourn Caxton End's conservation area designated in 1997 — volume-checked, set-back-detailed and drawn to South Cambridgeshire District Council's guidance.
Dormer loft drawings for Caldecote's conservation area designated in 1988 — volume-checked, set-back-detailed and drawn to South Cambridgeshire District Council's guidance.
Dormer loft drawings for Kingston's conservation area designated in 1974 — volume-checked, set-back-detailed and drawn to South Cambridgeshire District Council's guidance.
Dormer loft drawings for Little Gransden's conservation area designated in 2006 — volume-checked, set-back-detailed and drawn to South Cambridgeshire District Council's guidance.
Dormer loft drawings for Kingston's civil parish within Caldecote — volume-checked, set-back-detailed and drawn to South Cambridgeshire District Council's guidance.
Whether a dormer in Caldecote needs permission comes down to where it sits and how big the box is. This is how the cases compare.
| Dormer type | Permitted development? | What it gains | What South Cambridgeshire District Council checks |
|---|---|---|---|
| Rear box, within volume | Usually yes | Full-height room across the back | Volume total, 20cm eaves set-back |
| Rear box, over volume limit | No — full application | A larger room | How far over the allowance, bulk |
| Front or side dormer | No — full application | Light to the front rooms | Visibility from the street, character |
| Dormer in a conservation area | No — full application | Same space, extra scrutiny | Roof form and street appearance |
In conservation areas such as Bourn and Bourn Caxton End, Class B dormer rights are removed and every dormer needs a full application.
A fixed process built around how South Cambridgeshire District Council validates and decides dormer applications — most drawings are submission-ready within seven days of survey.
Send us your Caldecote postcode and roof type. We confirm your conservation and Article 4 status, work out how much permitted-development volume you have left, and score your odds against live South Cambridgeshire District Council decisions.
We measure ridge and eaves heights, roof pitch and the existing loft floor — the numbers the volume calculation, the set-back and the head heights depend on.
Chartered designers develop the box to your brief, drawn inside the Class B volume limits or, where those are exhausted or removed, to South Cambridgeshire District Council's roof-alteration guidance.
We submit the certificate or application, manage validation and case-officer queries, and revise the drawings free until South Cambridgeshire District Council issues its decision.
Often not. A rear box dormer within 40 cubic metres on a terrace, or 50 on a semi or detached house, set back at least 20 centimetres from the eaves and kept below the ridge, is usually permitted development. In Caldecote you will need a full application to South Cambridgeshire District Council for a front or side dormer, a box that exceeds the volume, and any dormer in a conservation area such as Bourn and Bourn Caxton End, where those rights are removed.
The permitted-development limit is a volume, not a footprint: 40 cubic metres of added roof space on a terraced house and 50 on a semi-detached or detached one, and any earlier loft enlargement counts against that total. In Caldecote the box must also sit below the ridge and back from the eaves. We measure your roof and calculate the exact volume you have left before drawing. South Cambridgeshire District Council is the decision-maker.
Not under permitted development. A dormer on the front roof slope, or one facing a highway, always needs a full application to South Cambridgeshire District Council, because it changes how the house reads from the street. Rear box dormers are far more likely to be approved — or to be permitted development outright — which is why almost every Caldecote dormer we draw sits on the back slope.
Often, on a terrace or semi. If the dormer or the loft steelwork meets the party wall with your neighbour, the Party Wall etc. Act applies and notice must be served before work starts — separately from South Cambridgeshire District Council's planning decision. We flag the party-wall junction on the drawings so a surveyor can be appointed early and the build is not held up. This applies to your Caldecote address specifically.
If your dormer is permitted development, a lawful development certificate from South Cambridgeshire District Council is council-stamped proof of it — worth holding, because a buyer's solicitor will ask for it when you sell. We prepare and submit the certificate with the same measured drawing pack that shows the box within its volume allowance. This applies to your Caldecote address specifically.
We price each Caldecote dormer individually, because the roof pitch and the volume left vary house to house, and send a fixed, no-obligation quote within one working day. It covers the full drawing pack with free revisions until South Cambridgeshire District Council approves, and we confirm at the outset whether your box is permitted development or needs an application. Call 020 7864 7245 to start.
Answer five quick questions and get a free planning score for your exact address — instantly. Then, if you want the full picture, unlock the detailed analysis: your council's live approval rates, local precedents, constraints on your street and a step-by-step route to permission.
Same fixed quotes, same fast drawings — wherever your project is.