Engineer's calculations for a Teynham and Lynsted project — steel beams sized, padstones and load paths worked out and a signed calculations package your builder and Swale Borough Council's building control can build from, delivered in days and revised free until it is approved.
Swale Borough Council granted 94% of the householder planning decisions it made in its latest published year — 7 points above the 87% England-wide householder average. Teynham and Lynsted contains Cellar Hill and Greenstreet, Teynham, Kingsdown, Lewson Street conservation areas (Cellar Hill and Greenstreet, Teynham designated 1970), so materials, fenestration and roof form are assessed against the appraisal, which is where a policy-literate drawing pack earns its keep. Its dominant Victorian (1837–1901) and postwar (1945–1970) housing stock sets the design brief on most streets.
Under Class B, a rear dormer stays permitted development up to 40m³ of added roof volume on a terrace or 50m³ on a semi-detached or detached house, while Class A allows a single-storey rear extension of 3m beyond the original rear wall on a terrace and 4m on a detached house before a full application is needed. Teynham and Lynsted carries at least one Article 4 direction, and conservation areas including Cellar Hill and Greenstreet, Teynham, Kingsdown and Lewson Street remove those rights outright, so we confirm your exact address before a line is drawn. A validated householder application in Teynham and Lynsted is determined against an 8-week statutory target.
Cellar Hill and Greenstreet, Teynham (conservation area designated in 1970), Kingsdown (conservation area designated in 1976), Lewson Street (conservation area designated in 1975), Lynsted - Bogle (conservation area designated in 1970), Lynsted - The Street (conservation area designated in 1970), Tonge (conservation area designated in 1987), Luddenham (civil parish within Teynham and Lynsted), Lynsted with Kingsdown (civil parish within Teynham and Lynsted), Norton, Buckland and Stone (civil parish within Teynham and Lynsted), Oare (civil parish within Teynham and Lynsted), Teynham (civil parish within Teynham and Lynsted) and Tonge (civil parish within Teynham and Lynsted) — these are the Teynham and Lynsted pockets our drawings cover most. Heritage designations here include Cellar Hill and Greenstreet, Teynham, Kingsdown, Lewson Street, Lynsted - Bogle, Lynsted - The Street and Tonge. Swale Borough Council weighs each proposal against Swale Borough Council's adopted local plan and its householder design guidance, where the 2,940 homes here are 28% pre-1900, 12% 1955-1964, 10% 1965-1972, which is what sets the realistic roof and rear-projection options. On roofs the borough is steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and shallow gabled roofs typical of that period's building, over Victorian and earlier houses (28% of 2,940 homes), late-1950s and early-1960s houses (12%) and late-1960s and early-1970s houses (10%).
Teynham and Lynsted's designated heritage is specific, and it is the first thing we check against your address: Cellar Hill and Greenstreet, Teynham (conservation area designated in 1970), Kingsdown (conservation area designated in 1976), Lewson Street (conservation area designated in 1975), Lynsted - Bogle (conservation area designated in 1970), Lynsted - The Street (conservation area designated in 1970) and Tonge (conservation area designated in 1987). Inside those boundaries permitted development is curtailed and Swale Borough Council assesses materials, window detail and roof form against the area's own appraisal, so a scheme that would be waved through two streets away can need a full application here.
Beyond the designated areas, Teynham and Lynsted takes in Luddenham, Lynsted with Kingsdown, Norton, Buckland and Stone, Oare, Teynham and Tonge. Swale Borough Council has 22 recorded Article 4 directions, removing permitted development for rear and side extensions — check the address before assuming PD applies in Teynham and Lynsted.
On stock, Teynham and Lynsted is Victorian and earlier houses (28% of 2,940 homes), late-1950s and early-1960s houses (12%) and late-1960s and early-1970s houses (10%) — which is why steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and shallow gabled roofs typical of that period's building govern what a loft or rear projection can realistically be. Swale Borough Council decided 329 householder applications in the latest published year and granted 94%, with 37% issued inside the eight-week target. Those are the numbers our drawings are prepared against.
The full build-period split for Teynham and Lynsted runs pre-1900 28% (810 homes), 1900-1918 0% (10 homes), 1919-1929 1% (20 homes), 1930-1939 5% (150 homes), 1945-1954 6% (190 homes), 1955-1964 12% (360 homes), 1965-1972 10% (300 homes), 1973-1982 3% (100 homes), 1983-1992 4% (110 homes), 1993-1999 4% (110 homes) and 2000-2008 4% (110 homes). That distribution is why pre-1900 detailing dominates the drawings here, and it is measured from council-tax records rather than assumed from the street name.
Swale Borough Council also decides for Abbey, Borden and Grove Park, Boughton and Courtenay, East Downs, Sheerness, Watling and West Downs, so a decision in Teynham and Lynsted sits inside a wider pattern of decisions we track across the same authority — useful when an officer cites a precedent from the next area over.
The Article 4 directions recorded for this council include 1 and 2 Flint Cottages, 20 East Street, 43-47, 49-51, 54, 56, 57, 59-72 Marine Parade and 49, 88, 90, 104, 114-128(evens), 132-140(evens) The Street and 1 & 2 Chapel Cottages. Each removes a specific permitted-development right inside its own boundary, which is why the check is done on the address rather than on the town.
Published figures for Teynham and Lynsted and Swale Borough Council. These are the numbers that decide what is realistic on your street, so we work from them rather than from national averages.
| Measure | Teynham and Lynsted |
|---|---|
| Dwellings recorded | 2,940 |
| Built pre-1900 | 810 (28%) |
| Built 1900-1918 | 10 (0%) |
| Built 1919-1929 | 20 (1%) |
| Built 1930-1939 | 150 (5%) |
| Built 1945-1954 | 190 (6%) |
| Built 1955-1964 | 360 (12%) |
| Built 1965-1972 | 300 (10%) |
| Built 1973-1982 | 100 (3%) |
| Built 1983-1992 | 110 (4%) |
| Built 1993-1999 | 110 (4%) |
| Built 2000-2008 | 110 (4%) |
| Built before 1919 | 28% |
| Built 1919–1939 | 6% |
| Built 1945–2008 | 44% |
| Conservation areas in Teynham and Lynsted | 6 (Cellar Hill and Greenstreet, Teynham, Kingsdown…) |
| Conservation areas district-wide | 52 |
| Article 4 directions recorded | 22 |
| Householder applications decided | 329 |
| Householder applications granted | 94% |
| Decided within 8 weeks | 37% |
Dwelling stock from VOA council-tax data at 31 March 2025; conservation-area and Article 4 counts from planning.data.gov.uk (MHCLG); decision figures are Swale Borough Council's own, from MHCLG live table PS2 for the year to 31 March 2026.
The moment a wall comes out or a new floor goes in, something has to carry the load that wall or floor was holding — and building control will not accept "it looks strong enough". The engineer traces the load path: the weight of the roof, floors and walls above is gathered into a beam, the beam is sized in steel or timber to carry it within safe deflection, and that load is passed through padstones into the masonry and down to the ground. On Teynham and Lynsted's Victorian and earlier houses (28% of 2,940 homes), late-1950s and early-1960s houses (12%) and late-1960s and early-1970s houses (10%), the spans and loads differ house to house, so every calculation is specific to the property.
The deliverable is two things that work together: the calculations, which show the maths an approved inspector can check, and the structural drawings, which turn that maths into something a builder can order and fit — a beam schedule with sizes and lengths, bearing and padstone details, and connection notes. Teynham and Lynsted contains Cellar Hill and Greenstreet, Teynham, Kingsdown, Lewson Street conservation areas (Cellar Hill and Greenstreet, Teynham designated 1970), so materials, fenestration and roof form are assessed against the appraisal, and the calculations are drawn to sit alongside the architectural set rather than contradict it. Everything is signed by a chartered or incorporated engineer carrying professional indemnity insurance.
Older Teynham and Lynsted stock — the kind found across Cellar Hill and Greenstreet, Teynham, Kingsdown, Lewson Street, Lynsted - Bogle, Lynsted - The Street and Tonge — often hides the real structural question: shallow Victorian foundations, timber that has been notched by past work, or a wall that turns out to be load-bearing when the drawings assumed otherwise. Swale Borough Council has 22 recorded Article 4 directions, removing permitted development for rear and side extensions — check the address before assuming PD applies in Teynham and Lynsted. A survey-based calculation catches this before the wall is opened, not after.
Building control needs an engineer's calculations whenever you change how the building carries load. On a typical Teynham and Lynsted project that means any of these:
We size the steel, work the padstones and bearings, trace the load to the foundations and issue a signed calculations package and a beam schedule for Swale Borough Council's building control — coordinated with your architectural drawings so the beam that is calculated is the beam that is drawn and the beam that is ordered.
Below is Swale Borough Council's real householder decision record, drawn from official planning statistics and refreshed as new data lands. Swale Borough Council granted 94% of its householder applications in the year to 31 March 2026, and Cellar Hill and Greenstreet, Teynham shapes what is approved here. Structural calculations sit behind building control rather than planning, but the same wave of loft, extension and knock-through work that drives these decisions is exactly what needs an engineer's package.
Source: MHCLG planning application statistics (householder decisions, England, 1 April 2025 - 31 March 2026). Compare every borough on our London approval-rate league table.
Tell us about your project and get a fixed, no-obligation quote back within one working day. If you don't need planning permission at all, we'll tell you that too — for free.
Building control approves structural work by checking the numbers, not by looking at the finished steel. Swale Borough Council's inspector, or an approved inspector acting for you, reads the calculations to confirm the beam is deep enough for its span, that deflection stays within limits so ceilings do not crack, that the bearing length and padstones spread the point load into masonry that can take it, and that the load has somewhere to go all the way to the ground. Across Cellar Hill and Greenstreet, Teynham, Kingsdown and Lewson Street, the recurring issue is a beam sized off a rule of thumb that the actual span will not support.
The 2,940 homes here are 28% pre-1900, 12% 1955-1964, 10% 1965-1972, which is what sets the realistic roof and rear-projection options. We issue calculations detailed enough to be signed off without a query, coordinate them with the architect's drawings so nothing conflicts on site, and stay available to revise if the builder finds the Teynham and Lynsted property is not quite as the survey assumed — free, until the work is approved.
We calculate beams, openings and floors on the period and modern stock across the borough. A few of the Teynham and Lynsted neighbourhoods where structural packages come up most often:
Structural calculations for Cellar Hill and Greenstreet, Teynham's conservation area designated in 1970 — beams sized, load paths traced and signed for Swale Borough Council's building control.
Structural calculations for Kingsdown's conservation area designated in 1976 — beams sized, load paths traced and signed for Swale Borough Council's building control.
Structural calculations for Lewson Street's conservation area designated in 1975 — beams sized, load paths traced and signed for Swale Borough Council's building control.
Structural calculations for Lynsted - Bogle's conservation area designated in 1970 — beams sized, load paths traced and signed for Swale Borough Council's building control.
Structural calculations for Lynsted - The Street's conservation area designated in 1970 — beams sized, load paths traced and signed for Swale Borough Council's building control.
Structural calculations for Tonge's conservation area designated in 1987 — beams sized, load paths traced and signed for Swale Borough Council's building control.
Different jobs load the building differently, so each needs its own calculation. This is what the common Teynham and Lynsted projects typically require.
| Project | Typical structure | What the calculation proves | Signed off by |
|---|---|---|---|
| Wall knock-through | Steel beam on padstones | Span, deflection and bearing | Building control |
| Loft conversion | New floor beams and ridge/purlin steels | Floor loading and roof support | Building control |
| Rear or side extension | Opening beam plus extension roof and floor | Combined loads and foundations | Building control |
| Basement or underpinning | Retaining and foundation design | Ground and adjacent-building loads | Building control & party wall |
On older Teynham and Lynsted stock around Cellar Hill and Greenstreet, Teynham and Kingsdown, shallow foundations and altered structure often mean the calculation drives the design rather than following it.
A fixed process built around building control rather than planning — most calculation packages are ready within five days of the architectural drawings.
Send us your Teynham and Lynsted postcode and the architect's drawings or a sketch. We confirm what structure the project needs, flag any load-bearing wall or foundation question, and tell you exactly what the calculation package will cover.
Where the loads are not obvious — an unknown wall, an old alteration, a deep span — we survey the property so the beam is sized on what is really there, not an assumption.
A chartered or incorporated engineer sizes the steel, works the padstones and load path, and issues the signed calculations and a beam schedule coordinated with your Teynham and Lynsted architectural set.
We submit the calculations to Swale Borough Council's building control or your approved inspector, answer queries, and revise free if the build uncovers something the survey could not see.
Whenever you change how the building carries weight — removing or opening a load-bearing wall, converting a loft, building an extension, or inserting a beam or column. Swale Borough Council's building control needs an engineer's calculation to approve any of these before the steel goes in. A Teynham and Lynsted project that only redecorates or moves a non-structural partition does not, but almost anything that opens the structure does.
No — they are a separate, later step. Planning permission decides whether Swale Borough Council will allow the change; structural calculations prove the change is safe to build and are submitted to building control, not to the planners. Many Teynham and Lynsted projects that need no planning permission at all — an internal knock-through, a permitted-development loft — still need a full engineer's calculation before work can lawfully start.
A chartered or incorporated structural engineer, carrying professional indemnity insurance, who takes responsibility for the numbers. Swale Borough Council's building control, or an approved inspector acting on your behalf, then checks and signs them off. Your builder cannot self-certify a steel beam, and an unsigned calculation will not be accepted — the engineer's signature and insurance are what make the package one building control will approve. This applies to your Teynham and Lynsted address specifically.
Yes — a beam over a removed wall is the most common calculation we do. We work out the load the wall was carrying, size a steel or timber beam to span the opening within safe deflection, and detail the padstones that spread its weight into the masonry each side. The result is a beam schedule your Teynham and Lynsted builder can order and Swale Borough Council's inspector can approve, with the load traced all the way to the foundations.
Sometimes. Where the loads are clear from the drawings we can calculate directly, but Teynham and Lynsted's older stock often hides surprises — a wall that turns out to be load-bearing, notched or altered joists, or shallow foundations near Cellar Hill and Greenstreet, Teynham and Kingsdown. In those cases a short structural survey means the beam is sized on what is really there, which avoids a redesign once the builder opens the wall. Swale Borough Council is the decision-maker.
We price each Teynham and Lynsted package on the number of beams and the complexity — a single knock-through is straightforward, a whole-house loft-and-extension scheme has several elements — and send a fixed, no-obligation quote within one working day. It covers the calculations, the beam schedule and free revisions until Swale Borough Council's building control approves. Call 020 7864 7245 to start.
Answer five quick questions and get a free planning score for your exact address — instantly. Then, if you want the full picture, unlock the detailed analysis: your council's live approval rates, local precedents, constraints on your street and a step-by-step route to permission.
Same fixed quotes, same fast drawings — wherever your project is.