Side-return infill drawings for Hulland terraces — the glazed extension that fills the redundant side alley and opens up the kitchen, drawn to Derbyshire Dales District Council's guidance, delivered in days and revised free until your decision, with a free approval-odds check first.
Derbyshire Dales District Council granted 93% of the householder planning decisions it made in its latest published year — 6 points above the 87% England-wide householder average. Hulland contains Hognaston, Hulland, Kirk Ireton conservation areas (Hognaston designated 1979), so materials, fenestration and roof form are assessed against the appraisal, which is where a policy-literate drawing pack earns its keep. Its dominant Victorian (1837–1901) and postwar (1945–1970) housing stock sets the design brief on most streets.
Class A and Class B set the thresholds — a rear dormer to 40m³ on a terrace or 50m³ on a semi or detached, and a single-storey rear extension to 3m on a terrace or 4m on a detached house — beyond which Derbyshire Dales District Council needs a full application. In conservation areas such as Hognaston, Hulland and Kirk Ireton those rights are removed, so we confirm your exact address before a line is drawn. A validated householder application in Hulland is determined against an 8-week statutory target.
Hognaston (conservation area designated in 1979), Hulland (conservation area designated in 1991), Kirk Ireton (conservation area designated in 1971), Hognaston (civil parish within Hulland), Hulland Ward (civil parish within Hulland), Kirk Ireton (civil parish within Hulland) and Biggin (civil parish within Hulland) — these are the Hulland pockets our drawings cover most. Heritage designations here include Hognaston, Hulland and Kirk Ireton. Derbyshire Dales District Council weighs each proposal against Derbyshire Dales District Council's development plan and the design policies it applies to householder applications, where the 920 homes here are 33% pre-1900, 20% 1965-1972, 11% 1973-1982, which is what sets the realistic roof and rear-projection options. On roofs the borough is steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and shallow-pitched roofs and integral garages typical of that period's building, over Victorian and earlier houses (33% of 920 homes), late-1960s and early-1970s houses (20%) and 1970s and early-1980s houses (11%).
Heritage designation is the single biggest variable in Hulland, and it is address-specific: Hognaston (conservation area designated in 1979), Hulland (conservation area designated in 1991) and Kirk Ireton (conservation area designated in 1971). Inside those boundaries permitted development is curtailed and Derbyshire Dales District Council assesses materials, window detail and roof form against the area's own appraisal, so a scheme that would be waved through two streets away can need a full application here.
Beyond the designated areas, Hulland takes in Hognaston, Hulland Ward, Kirk Ireton and Biggin. No Article 4 direction is recorded for Derbyshire Dales District Council, but Hulland's 3 conservation areas still limit permitted development on those streets.
On stock, Hulland is Victorian and earlier houses (33% of 920 homes), late-1960s and early-1970s houses (20%) and 1970s and early-1980s houses (11%) — which is why steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and shallow-pitched roofs and integral garages typical of that period's building govern what a loft or rear projection can realistically be. Derbyshire Dales District Council decided 189 householder applications in the latest published year and granted 93%, with 70% issued inside the eight-week target. We work from the council's own published record.
The full build-period split for Hulland runs pre-1900 33% (300 homes), 1930-1939 1% (10 homes), 1945-1954 4% (40 homes), 1955-1964 3% (30 homes), 1965-1972 20% (180 homes), 1973-1982 11% (100 homes), 1983-1992 3% (30 homes), 1993-1999 3% (30 homes) and 2000-2008 5% (50 homes). That distribution is why pre-1900 detailing dominates the drawings here, and it is measured from council-tax records rather than assumed from the street name.
Derbyshire Dales District Council also decides for Ashbourne North, Ashbourne South, Brailsford, Doveridge & Sudbury, Matlock East & Tansley, Matlock West, Norbury and Wirksworth, so a decision in Hulland sits inside a wider pattern of decisions we track across the same authority — useful when an officer cites a precedent from the next area over.
Published figures for Hulland and Derbyshire Dales District Council. These are the numbers that decide what is realistic on your street, so we work from them rather than from national averages.
| Measure | Hulland |
|---|---|
| Dwellings recorded | 920 |
| Built pre-1900 | 300 (33%) |
| Built 1930-1939 | 10 (1%) |
| Built 1945-1954 | 40 (4%) |
| Built 1955-1964 | 30 (3%) |
| Built 1965-1972 | 180 (20%) |
| Built 1973-1982 | 100 (11%) |
| Built 1983-1992 | 30 (3%) |
| Built 1993-1999 | 30 (3%) |
| Built 2000-2008 | 50 (5%) |
| Built before 1919 | 33% |
| Built 1919–1939 | 1% |
| Built 1945–2008 | 50% |
| Conservation areas in Hulland | 3 (Hognaston, Hulland…) |
| Conservation areas district-wide | 31 |
| Article 4 directions recorded | 0 |
| Householder applications decided | 189 |
| Householder applications granted | 93% |
| Decided within 8 weeks | 70% |
Dwelling stock from VOA council-tax data at 31 March 2025; conservation-area and Article 4 counts from planning.data.gov.uk (MHCLG); decision figures are Derbyshire Dales District Council's own, from MHCLG live table PS2 for the year to 31 March 2026.
The side return is the classic terrace fix, and Hulland has the stock for it — the borough is built largely from Victorian and earlier houses (33% of 920 homes), late-1960s and early-1970s houses (20%) and 1970s and early-1980s houses (11%), and the Victorian and Edwardian versions almost all have an L-shaped back addition with a wasted alley beside it. Fill that alley and the dark galley kitchen becomes a bright, square room the full width of the house. Derbyshire Dales District Council judges the infill against Derbyshire Dales District Council's development plan and the design policies it applies to householder applications, and because it runs along the party boundary, the neighbour relationship is read before the design.
That boundary is where the drawings earn their keep. We set the infill wall on or up to the line, keep the roof — usually a glazed lantern or a shallow pitch tying into the existing back-addition slope — below the neighbour's first-floor windows, and detail the rainwater and party-wall junction so the build is watertight and the Party Wall Act is satisfied. Hulland contains Hognaston, Hulland, Kirk Ireton conservation areas (Hognaston designated 1979), so materials, fenestration and roof form are assessed against the appraisal, so we resolve it on the section rather than leave it to the case officer.
Many of Hulland's terraces sit in conservation areas — Hognaston, Hulland and Kirk Ireton among them — where a side extension is no longer permitted development. No Article 4 direction is recorded for Derbyshire Dales District Council, but Hulland's 3 conservation areas still limit permitted development on those streets. We confirm the designation before a line is drawn.
Some single-storey side returns in Hulland are permitted development, but the width and boundary make an application more likely than for a straight rear extension. You will normally need to apply to Derbyshire Dales District Council if any of these apply:
We draw the infill wall on the boundary, the glazed roof below the neighbour's windows and the party-wall junction on the page — the details Derbyshire Dales District Council's officers and your neighbour both check — and submit a validation-complete pack, whether that is a lawful development certificate or a full householder application.
Below is Derbyshire Dales District Council's real householder decision record, drawn from official planning statistics and refreshed as new data lands. Derbyshire Dales District Council granted 93% of its householder applications in the year to 31 March 2026, and Hognaston shapes what is approved here. Side returns hinge on width, roof glazing and the party boundary, so a pack that resolves those details upfront is decided faster and refused less often than a DIY submission.
Source: MHCLG planning application statistics (householder decisions, England, 1 April 2025 - 31 March 2026). Compare every borough on our London approval-rate league table.
Tell us about your project and get a fixed, no-obligation quote back within one working day. If you don't need planning permission at all, we'll tell you that too — for free.
Across Hognaston, Hulland and Kirk Ireton, the approved side return is a single-storey infill roofed with a glazed lantern or roof light to pull daylight deep into the plan, its flank wall built on the boundary and finished to match the host brick. On the borough's victorian and earlier houses (33% of 920 homes), this is frequently the single biggest gain in usable ground-floor space, and where it stays within the width and height limits it can proceed under permitted development or a lawful development certificate.
The 920 homes here are 33% pre-1900, 20% 1965-1972, 11% 1973-1982, which is what sets the realistic roof and rear-projection options. We keep the glazed roof below the neighbour's cill line, set the gutter and the party-wall flashing so water and maintenance are designed in, and — where owners want the full open-plan room — pair the infill with a rear extension as a single wraparound application. That way Derbyshire Dales District Council sees one coherent scheme rather than two overlapping ones.
We draw side-return infills on every terraced street in the borough. A few of the neighbourhoods where Hulland side returns come up most often:
Side return extension drawings for Hognaston's conservation area designated in 1979 — width-checked, party-wall detailed and drawn to Derbyshire Dales District Council's guidance.
Side return extension drawings for Hulland's conservation area designated in 1991 — width-checked, party-wall detailed and drawn to Derbyshire Dales District Council's guidance.
Side return extension drawings for Kirk Ireton's conservation area designated in 1971 — width-checked, party-wall detailed and drawn to Derbyshire Dales District Council's guidance.
Side return extension drawings for Hognaston's civil parish within Hulland — width-checked, party-wall detailed and drawn to Derbyshire Dales District Council's guidance.
Side return extension drawings for Hulland Ward's civil parish within Hulland — width-checked, party-wall detailed and drawn to Derbyshire Dales District Council's guidance.
Side return extension drawings for Kirk Ireton's civil parish within Hulland — width-checked, party-wall detailed and drawn to Derbyshire Dales District Council's guidance.
Whether a side return in Hulland needs permission comes down to width, storeys and whether the street is designated. This is how the cases compare.
| Side return type | Permitted development? | What it gains | What Derbyshire Dales District Council checks |
|---|---|---|---|
| Single-storey infill, within limits | Often yes, if under half the house width | Full-width kitchen-diner | Width, 4m height, roof glazing |
| Single-storey, over half width | No — full application | Wider room, more light | Boundary treatment, neighbour amenity |
| Two-storey side return | No — full application | Room above as well as below | Bulk, overlooking, terrace rhythm |
| Wraparound (side + rear) | No — full application | L-shaped open-plan ground floor | Combined footprint, garden retained |
In conservation areas such as Hognaston and Hulland, side extensions are not permitted development and always need a full application.
A fixed process built around how Derbyshire Dales District Council validates and decides side-return applications — most drawings are submission-ready within seven days of survey.
Send us your Hulland postcode and terrace type. We confirm your conservation and Article 4 status, whether the infill stays within the side-extension width limit, and score your odds against live Derbyshire Dales District Council decisions.
We measure the side alley, the back-addition wall, floor and eaves levels and the neighbour's window heights — the numbers the width limit, roof pitch and party-wall detailing depend on.
Chartered designers develop the infill and its glazed roof to your brief, drawn inside the permitted-development limits or to Derbyshire Dales District Council's extension guidance, with the boundary and party-wall junction detailed.
We submit the certificate or application, manage validation and case-officer queries, and revise the drawings free until Derbyshire Dales District Council issues its decision.
Sometimes not. A single-storey side-return infill can be permitted development if it is no wider than half the original house, no higher than 4 metres, and the property is not on designated land. In Hulland you will need a full application to Derbyshire Dales District Council for anything wider or taller, for a two-storey side return, and for any side extension in a conservation area such as Hognaston and Hulland, where those rights are removed.
It is an infill that fills the narrow open alley running alongside the rear back-addition of a Victorian or Edwardian terrace — the strip of ground that is usually too small to use. Building over it squares off the ground floor, so a cramped galley kitchen becomes a full-width room. Hulland's period terraces are ideally suited to it, which is why the side return is one of the borough's most common extensions. Derbyshire Dales District Council is the decision-maker.
Almost always. A side return is built on or up to the boundary with your neighbour, so the Party Wall etc. Act applies and you must serve notice before work starts — this is entirely separate from Derbyshire Dales District Council's planning decision. We detail the party-wall junction on the drawings and flag the notice early so a surveyor can be appointed without delaying the build. This applies to your Hulland address specifically.
Yes, and it is common — the combined L-shape is a wraparound extension. Once the side infill joins a rear projection beyond the permitted-development depth, the whole thing needs a full householder application to Derbyshire Dales District Council rather than qualifying as permitted development. We draw it as one coherent scheme so the council assesses a single footprint, which reads more clearly than two overlapping proposals. This applies to your Hulland address specifically.
A householder planning application in Hulland runs to a statutory eight-week target, and a lawful development certificate to eight weeks as well, though an incomplete pack can stall at validation. Because a side return involves the boundary and roof glazing, a complete, well-detailed submission matters — we prepare it validation-complete and manage officer queries to keep the decision on track. Derbyshire Dales District Council is the decision-maker.
We price each Hulland side return individually, because alley width and roof form vary house to house, and send a fixed, no-obligation quote within one working day. It covers the full drawing pack with free revisions until Derbyshire Dales District Council approves, and we confirm at the outset whether your infill is permitted development or needs an application. Call 020 7864 7245 to start.
Answer five quick questions and get a free planning score for your exact address — instantly. Then, if you want the full picture, unlock the detailed analysis: your council's live approval rates, local precedents, constraints on your street and a step-by-step route to permission.
Same fixed quotes, same fast drawings — wherever your project is.