MCIAT chartered drawings · Fixed fees across all 33 London boroughs
Services
Areas
Guides
ProcessOur promiseFAQ
Free approval reportGet my free quote020 7864 7245
Porch extension plans in Box & Colerne — a front porch built onto the principal elevation of a house
Box & Colerne · Porch Drawings & Planning

Porch extension plans in Box & Colerne

Front-porch drawings for Box & Colerne homes — checked against the Class D permitted-development limits, drawn to Wiltshire Council's frontage guidance, delivered in days and revised free until your decision, with a free approval-odds check first.

★★★★★ Rated 4.9/5 by London homeowners96% approval rate · 2,400+ drawings delivered
Share

Box & Colerne householder planning by the numbers

Wiltshire Council granted 96% of the householder planning decisions it made in its latest published year — 9 points above the 87% England-wide householder average. Box & Colerne contains ASHLEY, BOX, COLERNE conservation areas (BOX designated 1975), so materials, fenestration and roof form are assessed against the appraisal, which is where a policy-literate drawing pack earns its keep. Its dominant Victorian (1837–1901) and postwar (1945–1970) housing stock sets the design brief on most streets.

Under Class B, a rear dormer stays permitted development up to 40m³ of added roof volume on a terrace or 50m³ on a semi-detached or detached house, while Class A allows a single-storey rear extension of 3m beyond the original rear wall on a terrace and 4m on a detached house before a full application is needed. Box & Colerne carries at least one Article 4 direction, and conservation areas including ASHLEY, BOX and COLERNE remove those rights outright, so we confirm your exact address before a line is drawn. A validated householder application in Box & Colerne is determined against an 8-week statutory target.

ASHLEY (designated conservation area), BOX (conservation area designated in 1975), COLERNE (conservation area designated in 1973), DITTERIDGE (designated conservation area), MIDDLEHILL (designated conservation area), Colerne (civil parish within Box & Colerne) and Box (civil parish within Box & Colerne) — these are the Box & Colerne pockets our drawings cover most. Heritage designations here include ASHLEY, BOX, COLERNE, DITTERIDGE and MIDDLEHILL. Wiltshire Council weighs each proposal against Wiltshire Council's adopted local plan and its householder design guidance, where the 2,560 homes here are 29% pre-1900, 18% 1955-1964, 16% 1965-1972, which is what sets the realistic roof and rear-projection options. On roofs the borough is steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and shallow gabled roofs typical of that period's building, over Victorian and earlier houses (29% of 2,560 homes), late-1950s and early-1960s houses (18%) and late-1960s and early-1970s houses (16%).

What actually constrains a project in Box & Colerne

Box & Colerne's designated heritage is specific, and it is the first thing we check against your address: ASHLEY (designated conservation area), BOX (conservation area designated in 1975), COLERNE (conservation area designated in 1973), DITTERIDGE (designated conservation area) and MIDDLEHILL (designated conservation area). Inside those boundaries permitted development is curtailed and Wiltshire Council assesses materials, window detail and roof form against the area's own appraisal, so a scheme that would be waved through two streets away can need a full application here.

Beyond the designated areas, Box & Colerne takes in Colerne and Box. Wiltshire Council has 48 recorded Article 4 directions, removing permitted development for rear and side extensions and other roof alterations, including rooflights — check the address before assuming PD applies in Box & Colerne.

On stock, Box & Colerne is Victorian and earlier houses (29% of 2,560 homes), late-1950s and early-1960s houses (18%) and late-1960s and early-1970s houses (16%) — which is why steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and shallow gabled roofs typical of that period's building govern what a loft or rear projection can realistically be. Wiltshire Council decided 1,779 householder applications in the latest published year and granted 96%, with 53% issued inside the eight-week target. Those are the numbers our drawings are prepared against.

The full build-period split for Box & Colerne runs pre-1900 29% (730 homes), 1900-1918 2% (50 homes), 1919-1929 2% (40 homes), 1930-1939 3% (80 homes), 1945-1954 14% (360 homes), 1955-1964 18% (450 homes), 1965-1972 16% (400 homes), 1973-1982 2% (40 homes), 1983-1992 4% (110 homes), 1993-1999 2% (60 homes) and 2000-2008 2% (50 homes). That distribution is why pre-1900 detailing dominates the drawings here, and it is measured from council-tax records rather than assumed from the street name.

Wiltshire Council also decides for Aldbourne & Ramsbury, Amesbury West, Avon Valley, By Brook, Corsham Ladbrook, Corsham Pickwick, Corsham Without and Cricklade & Latton, so a decision in Box & Colerne sits inside a wider pattern of decisions we track across the same authority — useful when an officer cites a precedent from the next area over.

The Article 4 directions recorded for this council include Ashley, Avebury, Baydon 1 and Baydon 2. Each removes a specific permitted-development right inside its own boundary, which is why the check is done on the address rather than on the town.

Box & Colerne in numbers — housing stock and planning decisions

Published figures for Box & Colerne and Wiltshire Council. These are the numbers that decide what is realistic on your street, so we work from them rather than from national averages.

MeasureBox & Colerne
Dwellings recorded2,560
Built pre-1900730 (29%)
Built 1900-191850 (2%)
Built 1919-192940 (2%)
Built 1930-193980 (3%)
Built 1945-1954360 (14%)
Built 1955-1964450 (18%)
Built 1965-1972400 (16%)
Built 1973-198240 (2%)
Built 1983-1992110 (4%)
Built 1993-199960 (2%)
Built 2000-200850 (2%)
Built before 191930%
Built 1919–19395%
Built 1945–200857%
Conservation areas in Box & Colerne5 (ASHLEY, BOX…)
Conservation areas district-wide245
Article 4 directions recorded48
Householder applications decided1,779
Householder applications granted96%
Decided within 8 weeks53%

Dwelling stock from VOA council-tax data at 31 March 2025; conservation-area and Article 4 counts from planning.data.gov.uk (MHCLG); decision figures are Wiltshire Council's own, from MHCLG live table PS2 for the year to 31 March 2026.

Why a porch is judged on the Box & Colerne street, not the plan

A porch is the smallest thing most people build and the most visible. It sits on the principal elevation, so Wiltshire Council reads it against the rhythm of the whole street rather than against your own house alone. Box & Colerne is largely Victorian and earlier houses (29% of 2,560 homes), late-1950s and early-1960s houses (18%) and late-1960s and early-1970s houses (16%), and where a run of houses shares one front-door detail, a porch that ignores it stands out from fifty metres away.

The three Class D numbers do most of the work: 3 square metres of external floor area, 3 metres of height, and a 2-metre stand-off from any boundary that fronts a highway. That last one catches more porches in Box & Colerne than the other two put together, because front gardens are shallow and the boundary is measured to the highway line, not to the kerb. We measure it on site and set the porch inside the limit, or we tell you honestly that it needs an application.

In Box & Colerne's conservation areas — ASHLEY, BOX, COLERNE, DITTERIDGE and MIDDLEHILL among them — a porch is assessed on materials, roof form and how the door surround is treated. Wiltshire Council has 48 recorded Article 4 directions, removing permitted development for rear and side extensions and other roof alterations, including rooflights — check the address before assuming PD applies in Box & Colerne.

Porch design drawing prepared for a Box & Colerne house frontage

Does a porch need planning permission in Box & Colerne?

Most modest porches are permitted development. You will need to apply to Wiltshire Council if any of these apply:

  • The external floor area measures more than 3 square metres
  • Any part of the porch stands higher than 3 metres above ground level
  • Any part sits within 2 metres of a boundary that fronts a highway
  • The house is in a conservation area such as ASHLEY and BOX, where frontage changes are controlled
  • The building is listed — listed building consent is required whatever the size
  • An Article 4 direction applies to your street — Wiltshire Council operates directions that can remove this right
  • The porch encloses a shared entrance to flats rather than a single house

Box & Colerne porch decisions — live from council data

Below is Wiltshire Council's real householder decision record, drawn from official planning statistics and refreshed as new data lands. Wiltshire Council granted 96% of its householder applications in the year to 31 March 2026, and ASHLEY shapes what is approved here. A porch application turns on frontage design and the highway stand-off, so a pack that dimensions both is decided faster than a sketch.

Source: MHCLG planning application statistics (householder decisions, England, 1 April 2025 - 31 March 2026). Compare every borough on our London approval-rate league table.

96%householder applications approved in Wiltshire
87%national average — Wiltshire is 9 points above the national average

Ready for drawings your council will approve?

Tell us about your project and get a fixed, no-obligation quote back within one working day. If you don't need planning permission at all, we'll tell you that too — for free.

Get your free fixed quote

60 seconds now. A fixed, no-obligation quote back within one working day — and we'll tell you if you don't even need planning.

No obligation · No spam · Reply within 1 working day

What porches get approved across Box & Colerne

Across ASHLEY, BOX and COLERNE, the porches that go through are the ones that borrow from the house: the same brick or render, a roof pitched to match, and a door and side-light proportioned to the original opening. On victorian and earlier houses (29% of 2,560 homes), an open-sided canopy is often the better answer than an enclosed porch — it stays clear of the floor-area limit and leaves the frontage legible.

Box & Colerne contains ASHLEY, BOX, COLERNE conservation areas (BOX designated 1975), so materials, fenestration and roof form are assessed against the appraisal, which is exactly the sort of local reading a porch has to satisfy. Where the 2-metre highway stand-off cannot be met, we either recess the porch behind the building line or prepare a full householder application with an elevation that shows the porch in the context of its neighbours — the drawing that answers the officer's real question.

Drawing pack for a porch application in Box & Colerne

Porch drawings across Box & Colerne

We draw porches on every street type in Box & Colerne. A few of the areas where porch work comes up most often:

ASHLEY

Porch drawings for ASHLEY — designated conservation area — dimensioned to the Class D limits and drawn to Wiltshire Council's frontage guidance.

BOX

Porch drawings for BOX — conservation area designated in 1975 — dimensioned to the Class D limits and drawn to Wiltshire Council's frontage guidance.

COLERNE

Porch drawings for COLERNE — conservation area designated in 1973 — dimensioned to the Class D limits and drawn to Wiltshire Council's frontage guidance.

DITTERIDGE

Porch drawings for DITTERIDGE — designated conservation area — dimensioned to the Class D limits and drawn to Wiltshire Council's frontage guidance.

MIDDLEHILL

Porch drawings for MIDDLEHILL — designated conservation area — dimensioned to the Class D limits and drawn to Wiltshire Council's frontage guidance.

Colerne

Porch drawings for Colerne — civil parish within Box & Colerne — dimensioned to the Class D limits and drawn to Wiltshire Council's frontage guidance.

Is your Box & Colerne porch permitted development or a full application?

Class D sets three thresholds. This is how the common cases fall either side of them.

Porch typePermitted development?What decides itWhat Wiltshire Council checks
Open canopy over the doorUsually yes — no enclosed floor areaWhether it is enclosedProjection, materials, roof form
Enclosed porch under 3m²Yes, if under 3m high and 2m from the highway boundaryExternal floor areaHighway stand-off, frontage design
Enclosed porch over 3m²No — full applicationExternal floor areaBulk on the principal elevation
Porch in a conservation areaOnly if it meets Class D and no Article 4 appliesDesignation statusMaterials, door detail, streetscape
Porch on a listed buildingNo — listed building consent requiredListingImpact on special interest

Thresholds from the Town and Country Planning (General Permitted Development) (England) Order 2015, Schedule 2, Part 1, Class D.

Four steps to an approved Box & Colerne porch

A fixed process built around how Wiltshire Council validates and decides frontage work — most porch drawings are submission-ready within seven days of survey.

  1. 1

    Free approval check

    Send us your Box & Colerne postcode. We confirm conservation, Article 4 and listing status, measure the front boundary against the 2-metre highway rule, and score your odds against live Wiltshire Council decisions.

  2. 2

    Measured survey

    We measure the frontage, threshold level, door opening and the distance to the highway boundary — the four numbers a porch application stands or falls on.

  3. 3

    Porch design & drawings

    Chartered designers develop the porch to your brief, either inside the Class D limits or as a full application drawn to Wiltshire Council's design guidance, with materials and roof form matched to the house.

  4. 4

    Submission & follow-through

    We submit the certificate or application, manage validation and case-officer queries, and revise the drawings free until Wiltshire Council issues its decision.

Frequently asked questions

Do I need planning permission for a porch in Box & Colerne?

Usually not, provided it meets all three Class D limits: no more than 3 square metres of external floor area, no more than 3 metres high, and no part within 2 metres of a boundary fronting a highway. Break any one and you need a householder application to Wiltshire Council. On designated land, and on listed buildings, the position is different and we check it before drawing. This applies to your Box & Colerne address specifically.

How is the 3 square metres measured on a Box & Colerne porch?

It is the external floor area — measured to the outside face of the porch walls, not the usable space inside. That catches people out, because a porch that feels small internally can exceed 3 square metres once the wall thickness is counted. We measure and dimension it on the plan so the figure is beyond argument at validation. This applies to your Box & Colerne address specifically. Wiltshire Council is the decision-maker.

What is the 2 metre highway rule for porches in Box & Colerne?

No part of a permitted-development porch may be within 2 metres of any boundary of the property that fronts a highway. In Box & Colerne this is the limit that most often pushes a porch into a full application, because front gardens are shallow. The measurement is to the boundary line, which is not always where the kerb or the fence sits — we establish it on survey. Wiltshire Council is the decision-maker.

Can I build a porch in a Box & Colerne conservation area?

Yes, but the design bar is higher. Class D is not automatically removed in a conservation area, so a compliant porch can still be permitted development — however Wiltshire Council will expect materials, roof pitch and door detail to respect the area's character, and an Article 4 direction can remove the right entirely. In ASHLEY and BOX we confirm the position on your specific address first. This applies to your Box & Colerne address specifically.

Does a porch need building regulations approval in Box & Colerne?

A porch is exempt from most building regulations if it is under 30 square metres, at ground level, separated from the house by the existing external door, and any glazing and electrics meet Parts K, N and P. Remove the original front door and the porch becomes part of the heated envelope, at which point insulation and Part L apply. We flag which side of that line your design falls on. This applies to your Box & Colerne address specifically. Wiltshire Council is the decision-maker.

How long does Wiltshire Council take to decide a porch application?

A householder application runs to an eight-week statutory target, and a lawful development certificate to the same. The realistic risk is not the decision but validation — an incomplete pack is returned rather than determined. We prepare the submission validation-complete and handle officer queries so the timetable holds. This applies to your Box & Colerne address specifically. Wiltshire Council is the decision-maker.

How much do porch plans in Box & Colerne cost?

We quote each Box & Colerne porch individually, because frontage type and boundary position vary house to house, and send a fixed, no-obligation quote within one working day. It covers the full drawing pack with free revisions until Wiltshire Council approves. Call 020 7864 7245 to start.

Planning approval report

Know your approval odds before you spend a penny on drawings

Answer five quick questions and get a free planning score for your exact address — instantly. Then, if you want the full picture, unlock the detailed analysis: your council's live approval rates, local precedents, constraints on your street and a step-by-step route to permission.

Porch extension plans across Wiltshire

Same fixed quotes, same fast drawings — wherever your project is.

Other planning services in Box & Colerne