
The full drawing set for a Tickhill & Wadsworth application — location and block plans, existing and proposed floor plans, elevations and sections, drawn to Doncaster Metropolitan Borough Council's validation checklist so the pack is accepted first time, delivered in days and revised free until your decision, with a free approval-odds check first.
Doncaster Metropolitan Borough Council granted 94% of the householder planning decisions it made in its latest published year — 7 points above the 87% England-wide householder average. Tickhill & Wadsworth contains Braithwell, Loversall, Stainton conservation areas (Braithwell designated 1979), so materials, fenestration and roof form are assessed against the appraisal, which is where a policy-literate drawing pack earns its keep. Its dominant postwar (1945–1970) housing stock sets the design brief on most streets.
Under Class B, a rear dormer stays permitted development up to 40m³ of added roof volume on a terrace or 50m³ on a semi-detached or detached house, while Class A allows a single-storey rear extension of 3m beyond the original rear wall on a terrace and 4m on a detached house before a full application is needed. Tickhill & Wadsworth carries at least one Article 4 direction, and conservation areas including Braithwell, Loversall and Stainton remove those rights outright, so we confirm your exact address before a line is drawn. A validated householder application in Tickhill & Wadsworth is determined against an 8-week statutory target.
Braithwell (conservation area designated in 1979), Loversall (conservation area designated in 1979), Stainton (conservation area designated in 1992), Tickhill (conservation area designated in 1970), Wadworth (conservation area designated in 1991), Braithwell (civil parish within Tickhill & Wadsworth), Loversall (civil parish within Tickhill & Wadsworth), Stainton (civil parish within Tickhill & Wadsworth), Tickhill (civil parish within Tickhill & Wadsworth) and Wadworth (civil parish within Tickhill & Wadsworth) — these are the Tickhill & Wadsworth pockets our drawings cover most. Heritage designations here include Braithwell, Loversall, Stainton, Tickhill and Wadworth. Doncaster Metropolitan Borough Council weighs each proposal against Doncaster Metropolitan Borough Council's adopted local plan and its householder design guidance, where the 5,810 homes here are 16% 1973-1982, 16% 2000-2008, 12% 1965-1972, which is what sets the realistic roof and rear-projection options. On roofs the borough is shallow trussed roofs typical of 1970s building and trussed-rafter roofs typical of 2000s building, over 1970s and early-1980s houses (16% of 5,810 homes), 2000s houses and apartments (16%) and late-1960s and early-1970s houses (12%).
Tickhill & Wadsworth's designated heritage is specific, and it is the first thing we check against your address: Braithwell (conservation area designated in 1979), Loversall (conservation area designated in 1979), Stainton (conservation area designated in 1992), Tickhill (conservation area designated in 1970) and Wadworth (conservation area designated in 1991). Inside those boundaries permitted development is curtailed and Doncaster Metropolitan Borough Council assesses materials, window detail and roof form against the area's own appraisal, so a scheme that would be waved through two streets away can need a full application here.
Beyond the designated areas, Tickhill & Wadsworth takes in Braithwell, Loversall, Stainton, Tickhill and Wadworth. Doncaster Metropolitan Borough Council has 3 recorded Article 4 directions — check the address before assuming PD applies in Tickhill & Wadsworth.
On stock, Tickhill & Wadsworth is 1970s and early-1980s houses (16% of 5,810 homes), 2000s houses and apartments (16%) and late-1960s and early-1970s houses (12%) — which is why shallow trussed roofs typical of 1970s building and trussed-rafter roofs typical of 2000s building govern what a loft or rear projection can realistically be. Doncaster Metropolitan Borough Council decided 432 householder applications in the latest published year and granted 94%, with 83% issued inside the eight-week target. Those are the numbers our drawings are prepared against.
The full build-period split for Tickhill & Wadsworth runs pre-1900 7% (390 homes), 1900-1918 2% (110 homes), 1919-1929 1% (80 homes), 1930-1939 6% (350 homes), 1945-1954 4% (210 homes), 1955-1964 6% (360 homes), 1965-1972 12% (690 homes), 1973-1982 16% (930 homes), 1983-1992 6% (350 homes), 1993-1999 6% (340 homes) and 2000-2008 16% (930 homes). That distribution is why pre-1900 detailing dominates the drawings here, and it is measured from council-tax records rather than assumed from the street name.
Doncaster Metropolitan Borough Council also decides for Bentley, Conisbrough, Edlington & Warmsworth, Finningley, Hatfield, Mexborough, Norton & Askern and Roman Ridge, so a decision in Tickhill & Wadsworth sits inside a wider pattern of decisions we track across the same authority — useful when an officer cites a precedent from the next area over.
The Article 4 directions recorded for this council include Article 4 (Balby Board School (DLHL04)) Boundary - Came into force 22 July 2024, Article 4 (DSA) Boundary - Came into force 25 July 2024 and Article 4 (HMO) Boundary - Came into force 14 October 2019. Each removes a specific permitted-development right inside its own boundary, which is why the check is done on the address rather than on the town.
Published figures for Tickhill & Wadsworth and Doncaster Metropolitan Borough Council. These are the numbers that decide what is realistic on your street, so we work from them rather than from national averages.
| Measure | Tickhill & Wadsworth |
|---|---|
| Dwellings recorded | 5,810 |
| Built pre-1900 | 390 (7%) |
| Built 1900-1918 | 110 (2%) |
| Built 1919-1929 | 80 (1%) |
| Built 1930-1939 | 350 (6%) |
| Built 1945-1954 | 210 (4%) |
| Built 1955-1964 | 360 (6%) |
| Built 1965-1972 | 690 (12%) |
| Built 1973-1982 | 930 (16%) |
| Built 1983-1992 | 350 (6%) |
| Built 1993-1999 | 340 (6%) |
| Built 2000-2008 | 930 (16%) |
| Built before 1919 | 9% |
| Built 1919–1939 | 7% |
| Built 1945–2008 | 66% |
| Conservation areas in Tickhill & Wadsworth | 5 (Braithwell, Loversall…) |
| Conservation areas district-wide | 38 |
| Article 4 directions recorded | 3 |
| Householder applications decided | 432 |
| Householder applications granted | 94% |
| Decided within 8 weeks | 83% |
Dwelling stock from VOA council-tax data at 31 March 2025; conservation-area and Article 4 counts from planning.data.gov.uk (MHCLG); decision figures are Doncaster Metropolitan Borough Council's own, from MHCLG live table PS2 for the year to 31 March 2026.
Whatever you are building, Doncaster Metropolitan Borough Council decides it from the same core set. A location plan at 1:1250 fixes the site on the map with the red-line boundary; a block plan at 1:500 shows the property in its plot; then existing and proposed floor plans and elevations at 1:100 or 1:50 show the house as it is and as it will be. Larger schemes add a section and, where policy requires, a design and access statement. Miss one and the application is returned invalid before an officer has looked at it.
The drawings are also the argument. Doncaster Metropolitan Borough Council assesses each proposal against Doncaster Metropolitan Borough Council's adopted local plan and its householder design guidance, and the elevations are where the case is won or lost — ridge and eaves heights, window positions, materials and how the change reads from the street. On Tickhill & Wadsworth's stock, which runs to 1970s and early-1980s houses (16% of 5,810 homes), 2000s houses and apartments (16%) and late-1960s and early-1970s houses (12%), the same scheme is drawn differently to answer the concerns officers raise here. Tickhill & Wadsworth contains Braithwell, Loversall, Stainton conservation areas (Braithwell designated 1979), so materials, fenestration and roof form are assessed against the appraisal, so the pack is built to pre-empt exactly that.
Where the property sits in a conservation area — Braithwell, Loversall, Stainton, Tickhill and Wadworth among Tickhill & Wadsworth's — validation is stricter still, often demanding heritage detail and sometimes additional plans. Doncaster Metropolitan Borough Council has 3 recorded Article 4 directions — check the address before assuming PD applies in Tickhill & Wadsworth. We confirm the designation before drawing so the pack meets the higher bar first time.

Doncaster Metropolitan Borough Council validates against a published checklist before it assesses anything. A typical householder application needs each of these, correctly scaled and labelled:
We draw the complete set — location and block plans, existing and proposed plans, elevations and any section — to Doncaster Metropolitan Borough Council's checklist, then lodge it on the Planning Portal, manage validation and answer case-officer queries so the application is decided on its merits, not bounced on a technicality.
Below is Doncaster Metropolitan Borough Council's real householder decision record, drawn from official planning statistics and refreshed as new data lands. Doncaster Metropolitan Borough Council granted 94% of its householder applications in the year to 31 March 2026, and Braithwell shapes what is approved here. A complete, correctly scaled pack that answers those concerns on the elevations is validated faster and refused less often than one that leaves them for the officer to raise.
Source: MHCLG planning application statistics (householder decisions, England, 1 April 2025 - 31 March 2026). Compare every borough on our London approval-rate league table.
Tell us about your project and get a fixed, no-obligation quote back within one working day. If you don't need planning permission at all, we'll tell you that too — for free.
Two different things sink an application, and they happen at two different stages. First is validation: a missing block plan, an unscaled elevation, no red line, no north point — Doncaster Metropolitan Borough Council returns the whole submission and the clock never starts. Getting the pack right at this stage is purely mechanical, and it is where a lot of self-submitted Tickhill & Wadsworth applications lose weeks. We draw to the checklist so this never happens.
Second is the planning judgement itself, once the pack is valid. The 5,810 homes here are 16% 1973-1982, 16% 2000-2008, 12% 1965-1972, which is what sets the realistic roof and rear-projection options. Across Braithwell, Loversall and Stainton the recurring refusals are about scale, overlooking and how the proposal sits against its neighbours — all of which are settled on the drawings. We draw the scheme to answer them before submission rather than after a refusal.

The application pack is the same discipline whatever the project. A few of the Tickhill & Wadsworth neighbourhoods and property types we prepare drawings for most often:
Planning drawings for Braithwell's conservation area designated in 1979 — scaled, validation-ready and drawn to Doncaster Metropolitan Borough Council's guidance.
Planning drawings for Loversall's conservation area designated in 1979 — scaled, validation-ready and drawn to Doncaster Metropolitan Borough Council's guidance.
Planning drawings for Stainton's conservation area designated in 1992 — scaled, validation-ready and drawn to Doncaster Metropolitan Borough Council's guidance.
Planning drawings for Tickhill's conservation area designated in 1970 — scaled, validation-ready and drawn to Doncaster Metropolitan Borough Council's guidance.
Planning drawings for Wadworth's conservation area designated in 1991 — scaled, validation-ready and drawn to Doncaster Metropolitan Borough Council's guidance.
Planning drawings for Braithwell's civil parish within Tickhill & Wadsworth — scaled, validation-ready and drawn to Doncaster Metropolitan Borough Council's guidance.
The route decides what Doncaster Metropolitan Borough Council needs and how long it takes. This is how the common Tickhill & Wadsworth routes compare.
| Route | When it applies | Core drawings | Typical decision |
|---|---|---|---|
| Householder application | Extensions and alterations to a single house | Location, block, existing & proposed plans and elevations | About 8 weeks |
| Full application | Flats, new units, changes of use | As householder plus site plan and often a section | 8–13 weeks |
| Lawful development certificate | Confirming a scheme is permitted development | Existing & proposed plans and elevations to prove PD limits | About 8 weeks |
| Prior approval | Larger single-storey rear extensions | Plans and elevations plus neighbour notification | About 6 weeks |
In a conservation area such as Braithwell and Loversall, householder permitted-development rights are often restricted, so a full application and heritage detail may be required.
A fixed process built around how Doncaster Metropolitan Borough Council validates and decides — most drawing sets are submission-ready within seven days of survey.
Send us your Tickhill & Wadsworth postcode and what you want to build. We confirm your conservation and Article 4 status, tell you which application route applies, and score your odds against live Doncaster Metropolitan Borough Council decisions.
We measure the property and plot so the existing plans and elevations are accurate to the millimetre — the base every proposed drawing and every officer judgement is built on.
Chartered designers produce the full validation pack — location and block plans, existing and proposed plans, elevations, any section and a design and access statement — drawn to Doncaster Metropolitan Borough Council's checklist.
We lodge the application on the Planning Portal, manage validation and case-officer queries, and revise the drawings free until Doncaster Metropolitan Borough Council issues its decision.
Doncaster Metropolitan Borough Council validates a householder application against a set list: a location plan at 1:1250 with a red-line boundary, a block plan at 1:500, and existing and proposed floor plans and elevations at 1:100 or 1:50, each with a scale bar and north point. Larger schemes and most conservation-area work also need a design and access statement. If any of these is missing or unscaled the application is returned invalid before it is assessed. This applies to your Tickhill & Wadsworth address specifically.
Almost always because the drawing pack is incomplete or wrongly scaled — a missing block plan, an elevation with no scale, no red line on the location plan, no north point. Doncaster Metropolitan Borough Council checks the pack against its validation list before an officer ever assesses the scheme, so these purely technical gaps cost weeks. Drawing to the checklist from the outset is the simplest way to avoid a return. This applies to your Tickhill & Wadsworth address specifically.
Yes. We prepare the full drawing set, lodge it on the Planning Portal on your behalf, pay the Doncaster Metropolitan Borough Council fee where you prefer us to, and then manage validation and case-officer questions through to the decision. You get the reference number and updates without dealing with the portal or the council yourself. This applies to your Tickhill & Wadsworth address specifically.
A householder application is a statutory eight weeks from validation, and a full application eight to thirteen weeks depending on scale. The date that matters is validation, not submission — an invalid pack never starts the clock. Because we draw to Doncaster Metropolitan Borough Council's checklist the application validates quickly, so the statutory period begins without the delay a returned pack causes. This applies to your Tickhill & Wadsworth address specifically.
You do not strictly need a planning application, but scaled existing and proposed drawings are still worth having: a lawful development certificate from Doncaster Metropolitan Borough Council proves the scheme is permitted development, which lenders and buyers increasingly ask for, and your builder needs the drawings to price and build. In a conservation area such as Braithwell and Loversall, permitted-development rights are often removed, so a full application may be needed after all — we confirm which before you commit. This applies to your Tickhill & Wadsworth address specifically.
We price each Tickhill & Wadsworth job individually — the scope of the survey and the size of the drawing set vary from a simple rear extension to a whole-house scheme — and send a fixed, no-obligation quote within one working day. It covers the full validation pack with free revisions until Doncaster Metropolitan Borough Council decides. The Doncaster Metropolitan Borough Council application fee is separate and paid to the council. Call 020 7864 7245 to start.
Answer five quick questions and get a free planning score for your exact address — instantly. Then, if you want the full picture, unlock the detailed analysis: your council's live approval rates, local precedents, constraints on your street and a step-by-step route to permission.
Same fixed quotes, same fast drawings — wherever your project is.