The full drawing set for a Erewash application — location and block plans, existing and proposed floor plans, elevations and sections, drawn to Erewash Borough Council's validation checklist so the pack is accepted first time, delivered in days and revised free until your decision, with a free approval-odds check first.
Erewash Borough Council granted 97% of the householder planning decisions it made in its latest published year — 10 points above the 87% England-wide householder average. Erewash contains Breadsall, Draycott, Eaton Bank conservation areas (Breadsall designated 1978), so materials, fenestration and roof form are assessed against the appraisal, which is where a policy-literate drawing pack earns its keep. Its dominant Victorian (1837–1901), interwar (1918–1939) and postwar (1945–1970) housing stock sets the design brief on most streets.
Before permission is required, Class B allows 40m³ of added loft volume on a terrace and 50m³ on a semi or detached house, and Class A allows a 3m single-storey rear extension on a terrace or 4m on a detached house. In conservation areas such as Breadsall, Draycott and Eaton Bank those rights are removed, so we confirm your exact address before a line is drawn. A validated householder application in Erewash is determined against an 8-week statutory target.
Breadsall (conservation area designated in 1978), Draycott (conservation area designated in 1978), Eaton Bank (conservation area designated in 1978), Little Eaton (conservation area designated in 1978), Long Eaton (Derby Road) (conservation area designated in 2011), Long Eaton Lace Factories (conservation area designated in 2005), Morley (conservation area designated in 1978), Ockbrook Moravian Settlement (conservation area designated in 1978), Derby Road East (ward of Erewash), Derby Road West (ward of Erewash), Draycott & Risley (ward of Erewash), Little Eaton & Stanley (ward of Erewash), Ockbrook & Borrowash (ward of Erewash) and Sandiacre (ward of Erewash) — these are the Erewash pockets our drawings cover most. Heritage designations here include Breadsall, Draycott, Eaton Bank, Little Eaton, Long Eaton (Derby Road), Long Eaton Lace Factories, Morley and Ockbrook Moravian Settlement. Erewash Borough Council weighs each proposal against the adopted Erewash local plan and Erewash Borough Council's design guidance for householder work, where the 17,260 homes here are 12% pre-1900, 9% 1930-1939, 9% 1955-1964, which is what sets the realistic roof and rear-projection options. On roofs the borough is steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and hipped roofs with shallow pitches typical of 1930s building, over Victorian and earlier houses (12% of 17,260 homes), 1930s semi-detached and detached houses (9%) and late-1950s and early-1960s houses (9%).
What is permitted in Erewash turns on designation first, so that is where we start: Breadsall (conservation area designated in 1978), Draycott (conservation area designated in 1978), Eaton Bank (conservation area designated in 1978), Little Eaton (conservation area designated in 1978), Long Eaton (Derby Road) (conservation area designated in 2011), Long Eaton Lace Factories (conservation area designated in 2005), Morley (conservation area designated in 1978) and Ockbrook Moravian Settlement (conservation area designated in 1978). Inside those boundaries permitted development is curtailed and Erewash Borough Council assesses materials, window detail and roof form against the area's own appraisal, so a scheme that would be waved through two streets away can need a full application here.
Beyond the designated areas, Erewash takes in Derby Road East, Derby Road West, Draycott & Risley, Little Eaton & Stanley, Ockbrook & Borrowash and Sandiacre. No Article 4 direction is recorded for Erewash Borough Council, but the district's 8 conservation areas still limit permitted development on those streets.
On stock, Erewash is Victorian and earlier houses (12% of 17,260 homes), 1930s semi-detached and detached houses (9%) and late-1950s and early-1960s houses (9%) — which is why steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and hipped roofs with shallow pitches typical of 1930s building govern what a loft or rear projection can realistically be. Erewash Borough Council decided 231 householder applications in the latest published year and granted 97%, with 62% issued inside the eight-week target. We draw to that record rather than to a national average.
The full build-period split for Erewash runs pre-1900 3% (190 homes), 1900-1918 0% (30 homes), 1919-1929 0% (10 homes), 1930-1939 6% (350 homes), 1945-1954 3% (170 homes), 1955-1964 30% (1,850 homes), 1965-1972 33% (1,990 homes), 1973-1982 4% (260 homes), 1983-1992 5% (310 homes), 1993-1999 4% (220 homes) and 2000-2008 3% (170 homes). That distribution is why pre-1900 detailing dominates the drawings here, and it is measured from council-tax records rather than assumed from the street name.
Erewash Borough Council also decides for Derby Road East, Derby Road West, Draycott & Risley, Little Eaton & Stanley, Ockbrook & Borrowash and Sandiacre, so a decision in Erewash sits inside a wider pattern of decisions we track across the same authority — useful when an officer cites a precedent from the next area over.
Published figures for Erewash and Erewash Borough Council. These are the numbers that decide what is realistic on your street, so we work from them rather than from national averages.
| Measure | Erewash |
|---|---|
| Dwellings recorded | 17,260 |
| Built pre-1900 | 190 (3%) |
| Built 1900-1918 | 30 (0%) |
| Built 1919-1929 | 10 (0%) |
| Built 1930-1939 | 350 (6%) |
| Built 1945-1954 | 170 (3%) |
| Built 1955-1964 | 1,850 (30%) |
| Built 1965-1972 | 1,990 (33%) |
| Built 1973-1982 | 260 (4%) |
| Built 1983-1992 | 310 (5%) |
| Built 1993-1999 | 220 (4%) |
| Built 2000-2008 | 170 (3%) |
| Built before 1919 | 23% |
| Built 1919–1939 | 19% |
| Built 1945–2008 | 53% |
| Conservation areas in Erewash | 8 (Breadsall, Draycott…) |
| Conservation areas district-wide | 22 |
| Article 4 directions recorded | 0 |
| Householder applications decided | 231 |
| Householder applications granted | 97% |
| Decided within 8 weeks | 62% |
Dwelling stock from VOA council-tax data at 31 March 2025; conservation-area and Article 4 counts from planning.data.gov.uk (MHCLG); decision figures are Erewash Borough Council's own, from MHCLG live table PS2 for the year to 31 March 2026.
Whatever you are building, Erewash Borough Council decides it from the same core set. A location plan at 1:1250 fixes the site on the map with the red-line boundary; a block plan at 1:500 shows the property in its plot; then existing and proposed floor plans and elevations at 1:100 or 1:50 show the house as it is and as it will be. Larger schemes add a section and, where policy requires, a design and access statement. Miss one and the application is returned invalid before an officer has looked at it.
The drawings are also the argument. Erewash Borough Council assesses each proposal against the adopted Erewash local plan and Erewash Borough Council's design guidance for householder work, and the elevations are where the case is won or lost — ridge and eaves heights, window positions, materials and how the change reads from the street. On Erewash's stock, which runs to Victorian and earlier houses (12% of 17,260 homes), 1930s semi-detached and detached houses (9%) and late-1950s and early-1960s houses (9%), the same scheme is drawn differently to answer the concerns officers raise here. Erewash contains Breadsall, Draycott, Eaton Bank conservation areas (Breadsall designated 1978), so materials, fenestration and roof form are assessed against the appraisal, so the pack is built to pre-empt exactly that.
Where the property sits in a conservation area — Breadsall, Draycott, Eaton Bank, Little Eaton, Long Eaton (Derby Road), Long Eaton Lace Factories, Morley and Ockbrook Moravian Settlement among Erewash's — validation is stricter still, often demanding heritage detail and sometimes additional plans. No Article 4 direction is recorded for Erewash Borough Council, but the district's 8 conservation areas still limit permitted development on those streets. We confirm the designation before drawing so the pack meets the higher bar first time.
Erewash Borough Council validates against a published checklist before it assesses anything. A typical householder application needs each of these, correctly scaled and labelled:
We draw the complete set — location and block plans, existing and proposed plans, elevations and any section — to Erewash Borough Council's checklist, then lodge it on the Planning Portal, manage validation and answer case-officer queries so the application is decided on its merits, not bounced on a technicality.
Below is Erewash Borough Council's real householder decision record, drawn from official planning statistics and refreshed as new data lands. Erewash Borough Council granted 97% of 231 householder decisions in the year to 31 March 2026, 62% of them inside eight weeks. A complete, correctly scaled pack that answers those concerns on the elevations is validated faster and refused less often than one that leaves them for the officer to raise.
Source: MHCLG planning application statistics (householder decisions, England, 1 April 2025 - 31 March 2026). Compare every borough on our London approval-rate league table.
Tell us about your project and get a fixed, no-obligation quote back within one working day. If you don't need planning permission at all, we'll tell you that too — for free.
Two different things sink an application, and they happen at two different stages. First is validation: a missing block plan, an unscaled elevation, no red line, no north point — Erewash Borough Council returns the whole submission and the clock never starts. Getting the pack right at this stage is purely mechanical, and it is where a lot of self-submitted Erewash applications lose weeks. We draw to the checklist so this never happens.
Second is the planning judgement itself, once the pack is valid. The 17,260 homes here are 12% pre-1900, 9% 1930-1939, 9% 1955-1964, which is what sets the realistic roof and rear-projection options. Across Breadsall, Draycott and Eaton Bank the recurring refusals are about scale, overlooking and how the proposal sits against its neighbours — all of which are settled on the drawings. We draw the scheme to answer them before submission rather than after a refusal.
The application pack is the same discipline whatever the project. A few of the Erewash neighbourhoods and property types we prepare drawings for most often:
Planning drawings for Breadsall's conservation area designated in 1978 — scaled, validation-ready and drawn to Erewash Borough Council's guidance.
Planning drawings for Draycott's conservation area designated in 1978 — scaled, validation-ready and drawn to Erewash Borough Council's guidance.
Planning drawings for Eaton Bank's conservation area designated in 1978 — scaled, validation-ready and drawn to Erewash Borough Council's guidance.
Planning drawings for Little Eaton's conservation area designated in 1978 — scaled, validation-ready and drawn to Erewash Borough Council's guidance.
Planning drawings for Long Eaton (Derby Road)'s conservation area designated in 2011 — scaled, validation-ready and drawn to Erewash Borough Council's guidance.
Planning drawings for Long Eaton Lace Factories's conservation area designated in 2005 — scaled, validation-ready and drawn to Erewash Borough Council's guidance.
The route decides what Erewash Borough Council needs and how long it takes. This is how the common Erewash routes compare.
| Route | When it applies | Core drawings | Typical decision |
|---|---|---|---|
| Householder application | Extensions and alterations to a single house | Location, block, existing & proposed plans and elevations | About 8 weeks |
| Full application | Flats, new units, changes of use | As householder plus site plan and often a section | 8–13 weeks |
| Lawful development certificate | Confirming a scheme is permitted development | Existing & proposed plans and elevations to prove PD limits | About 8 weeks |
| Prior approval | Larger single-storey rear extensions | Plans and elevations plus neighbour notification | About 6 weeks |
In a conservation area such as Breadsall and Draycott, householder permitted-development rights are often restricted, so a full application and heritage detail may be required.
A fixed process built around how Erewash Borough Council validates and decides — most drawing sets are submission-ready within seven days of survey.
Send us your Erewash postcode and what you want to build. We confirm your conservation and Article 4 status, tell you which application route applies, and score your odds against live Erewash Borough Council decisions.
We measure the property and plot so the existing plans and elevations are accurate to the millimetre — the base every proposed drawing and every officer judgement is built on.
Chartered designers produce the full validation pack — location and block plans, existing and proposed plans, elevations, any section and a design and access statement — drawn to Erewash Borough Council's checklist.
We lodge the application on the Planning Portal, manage validation and case-officer queries, and revise the drawings free until Erewash Borough Council issues its decision.
Erewash Borough Council validates a householder application against a set list: a location plan at 1:1250 with a red-line boundary, a block plan at 1:500, and existing and proposed floor plans and elevations at 1:100 or 1:50, each with a scale bar and north point. Larger schemes and most conservation-area work also need a design and access statement. If any of these is missing or unscaled the application is returned invalid before it is assessed.
Almost always because the drawing pack is incomplete or wrongly scaled — a missing block plan, an elevation with no scale, no red line on the location plan, no north point. Erewash Borough Council checks the pack against its validation list before an officer ever assesses the scheme, so these purely technical gaps cost weeks. Drawing to the checklist from the outset is the simplest way to avoid a return.
Yes. We prepare the full drawing set, lodge it on the Planning Portal on your behalf, pay the Erewash Borough Council fee where you prefer us to, and then manage validation and case-officer questions through to the decision. You get the reference number and updates without dealing with the portal or the council yourself.
A householder application is a statutory eight weeks from validation, and a full application eight to thirteen weeks depending on scale. The date that matters is validation, not submission — an invalid pack never starts the clock. Because we draw to Erewash Borough Council's checklist the application validates quickly, so the statutory period begins without the delay a returned pack causes.
You do not strictly need a planning application, but scaled existing and proposed drawings are still worth having: a lawful development certificate from Erewash Borough Council proves the scheme is permitted development, which lenders and buyers increasingly ask for, and your builder needs the drawings to price and build. In a conservation area such as Breadsall and Draycott, permitted-development rights are often removed, so a full application may be needed after all — we confirm which before you commit.
We price each Erewash job individually — the scope of the survey and the size of the drawing set vary from a simple rear extension to a whole-house scheme — and send a fixed, no-obligation quote within one working day. It covers the full validation pack with free revisions until Erewash Borough Council decides. The Erewash Borough Council application fee is separate and paid to the council. Call 020 7864 7245 to start.
Answer five quick questions and get a free planning score for your exact address — instantly. Then, if you want the full picture, unlock the detailed analysis: your council's live approval rates, local precedents, constraints on your street and a step-by-step route to permission.
Same fixed quotes, same fast drawings — wherever your project is.