MCIAT chartered drawings · Fixed fees across all 33 London boroughs
Services
Areas
Guides
ProcessOur promiseFAQ
Free approval reportGet my free quote020 7864 7245
Listed building consent drawings in Burton and Holme — historic building fabric recorded before alteration
Burton and Holme · Listed Building Consent

Listed building consent drawings in Burton and Holme

Listed building consent drawings for Burton and Holme — measured as existing, proposed in the same detail, and supported by a heritage statement that answers Westmorland and Furness Council's conservation officer on the terms the 1990 Act actually sets.

★★★★★ Rated 4.9/5 by London homeowners96% approval rate · 2,400+ drawings delivered
Share

What the data says about planning in Burton and Holme

Westmorland and Furness Council granted 93% of the householder planning decisions it made in its latest published year — 6 points above the 87% England-wide householder average. Burton and Holme contains the Burton conservation area (Burton designated 1969), so materials, fenestration and roof form are assessed against the appraisal, which is where a policy-literate drawing pack earns its keep. Its dominant Victorian (1837–1901) and postwar (1945–1970) housing stock sets the design brief on most streets.

Class A and Class B set the thresholds — a rear dormer to 40m³ on a terrace or 50m³ on a semi or detached, and a single-storey rear extension to 3m on a terrace or 4m on a detached house — beyond which Westmorland and Furness Council needs a full application. In conservation areas such as Burton those rights are removed, so we confirm your exact address before a line is drawn. A validated householder application in Burton and Holme is determined against an 8-week statutory target.

Burton (conservation area designated in 1969), Holme (civil parish within Burton and Holme), Hutton Roof (civil parish within Burton and Holme), Lupton (civil parish within Burton and Holme), Mansergh (civil parish within Burton and Holme) and Burton-in-Kendal (civil parish within Burton and Holme) — these are the Burton and Holme pockets our drawings cover most. Heritage designations here include Burton. Westmorland and Furness Council weighs each proposal against the adopted Westmorland and Furness local plan and Westmorland and Furness Council's design guidance for householder work, where the 1,440 homes here are 22% pre-1900, 22% 1965-1972, 13% 2000-2008, which is what sets the realistic roof and rear-projection options. On roofs the borough is steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and shallow-pitched roofs and integral garages typical of that period's building, over Victorian and earlier houses (22% of 1,440 homes), late-1960s and early-1970s houses (22%) and 2000s houses and apartments (13%).

Designations, stock and decisions in Burton and Holme

Heritage designation is the single biggest variable in Burton and Holme, and it is address-specific: Burton (conservation area designated in 1969). Inside those boundaries permitted development is curtailed and Westmorland and Furness Council assesses materials, window detail and roof form against the area's own appraisal, so a scheme that would be waved through two streets away can need a full application here.

Beyond the designated areas, Burton and Holme takes in Holme, Hutton Roof, Lupton, Mansergh and Burton-in-Kendal. No Article 4 direction is recorded for Westmorland and Furness Council, but Burton and Holme's 1 conservation area still limit permitted development on those streets.

On stock, Burton and Holme is Victorian and earlier houses (22% of 1,440 homes), late-1960s and early-1970s houses (22%) and 2000s houses and apartments (13%) — which is why steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and shallow-pitched roofs and integral garages typical of that period's building govern what a loft or rear projection can realistically be. Westmorland and Furness Council decided 508 householder applications in the latest published year and granted 93%, with 51% issued inside the eight-week target. We work from the council's own published record.

The full build-period split for Burton and Holme runs pre-1900 22% (320 homes), 1900-1918 1% (20 homes), 1930-1939 1% (20 homes), 1945-1954 6% (90 homes), 1955-1964 3% (40 homes), 1965-1972 22% (310 homes), 1973-1982 6% (80 homes), 1983-1992 12% (170 homes), 1993-1999 3% (50 homes) and 2000-2008 13% (190 homes). That distribution is why pre-1900 detailing dominates the drawings here, and it is measured from council-tax records rather than assumed from the street name.

Westmorland and Furness Council also decides for Alston and Fellside, Appleby and Brough, Eden and Lyvennet Vale, Grange and Cartmel, Hesket and Lazonby, High Furness, Kent Estuary and Levens and Crooklands, so a decision in Burton and Holme sits inside a wider pattern of decisions we track across the same authority — useful when an officer cites a precedent from the next area over.

The published numbers behind a Burton and Holme application

Published figures for Burton and Holme and Westmorland and Furness Council. These are the numbers that decide what is realistic on your street, so we work from them rather than from national averages.

MeasureBurton and Holme
Dwellings recorded1,440
Built pre-1900320 (22%)
Built 1900-191820 (1%)
Built 1930-193920 (1%)
Built 1945-195490 (6%)
Built 1955-196440 (3%)
Built 1965-1972310 (22%)
Built 1973-198280 (6%)
Built 1983-1992170 (12%)
Built 1993-199950 (3%)
Built 2000-2008190 (13%)
Built before 191924%
Built 1919–19391%
Built 1945–200865%
Conservation areas in Burton and Holme1 (Burton)
Conservation areas district-wide40
Article 4 directions recorded0
Householder applications decided508
Householder applications granted93%
Decided within 8 weeks51%

Dwelling stock from VOA council-tax data at 31 March 2025; conservation-area and Article 4 counts from planning.data.gov.uk (MHCLG); decision figures are Westmorland and Furness Council's own, from MHCLG live table PS2 for the year to 31 March 2026.

What consent actually protects in a Burton and Holme listed building

Listing protects the whole building, not the front elevation. Removing a partition, replacing a staircase balustrade, changing a floor finish, or lining a wall with insulation are all alterations to special interest, and all can require consent. That surprises owners far more often than the external rules do — and it is why the first deliverable on a listed project is an accurate record of what is there, not a proposal for what replaces it.

Burton and Holme sits within an area of Victorian and earlier houses (22% of 1,440 homes), late-1960s and early-1970s houses (22%) and 2000s houses and apartments (13%), and its designated heritage includes Burton. Conservation-area designation and listing are different things and frequently overlap: a listed house inside a conservation area needs consent for internal work under the listing, and is judged on its contribution to the wider area under the designation. We establish both before proposing anything.

Section 16(2) of the 1990 Act requires Westmorland and Furness Council to have special regard to the desirability of preserving the building, its setting and any features of special architectural or historic interest. In practice that means the drawings must show what is being lost as clearly as what is being gained, and the case for the intervention must be made on heritage terms rather than on convenience.

Survey drawing of listed building fabric in Burton and Holme

When do you need listed building consent in Burton and Holme?

Consent from Westmorland and Furness Council is required for works affecting special interest. That commonly includes:

  • Removing, altering or forming internal walls, doorways or staircases
  • Replacing windows or doors, including like-for-like where detail changes
  • Re-roofing in a different material, or altering chimneys
  • Internal insulation, damp treatment or re-plastering in historic fabric
  • New services routed through historic fabric — heating, wiring, ventilation
  • Works to curtilage structures such as walls, outbuildings and railings
  • Demolition of any part of the building, however small
  • Signage, external lighting or satellite equipment fixed to the building

Burton and Holme heritage decisions — live from council data

Below is Westmorland and Furness Council's real decision record, drawn from official planning statistics and refreshed as new data lands. Westmorland and Furness Council granted 93% of its householder applications in the year to 31 March 2026, and Burton shapes what is approved here. Listed applications are decided on the quality of the record and the justification, which is where most refusals actually originate.

Source: MHCLG planning application statistics (householder decisions, England, 1 April 2025 - 31 March 2026). Compare every borough on our London approval-rate league table.

93%householder applications approved in Westmorland and Furness
87%national average — Westmorland and Furness is 6 points above the national average

Ready for drawings your council will approve?

Tell us about your project and get a fixed, no-obligation quote back within one working day. If you don't need planning permission at all, we'll tell you that too — for free.

Get your free fixed quote

60 seconds now. A fixed, no-obligation quote back within one working day — and we'll tell you if you don't even need planning.

No obligation · No spam · Reply within 1 working day

What gets consented on listed buildings in Burton and Holme

Across Burton, Holme and Hutton Roof, the schemes that get consent tend to be reversible, legible and honest: new work that reads as new rather than as imitation, services routed in existing chases rather than cut into original fabric, and interventions concentrated in later or lower-significance parts of the building. Rear additions in a contemporary idiom are often accepted where a pastiche extension is refused.

Burton and Holme contains the Burton conservation area (Burton designated 1969), so materials, fenestration and roof form are assessed against the appraisal. Where planning permission is needed as well — for an extension, say — the two applications run in parallel and are usually determined together. We prepare them as a single coordinated set so the heritage case and the planning case do not contradict each other, which is a surprisingly common reason for a refusal on an otherwise sound scheme.

Listed building consent drawing pack for a property in Burton and Holme

Listed building work across Burton and Holme

We prepare listed building consent packs across Burton and Holme. A few of the areas where heritage work comes up most often:

Burton

Listed building consent drawings for Burton — conservation area designated in 1969 — surveyed as existing and drawn to the detail Westmorland and Furness Council's conservation officer needs.

Holme

Listed building consent drawings for Holme — civil parish within Burton and Holme — surveyed as existing and drawn to the detail Westmorland and Furness Council's conservation officer needs.

Hutton Roof

Listed building consent drawings for Hutton Roof — civil parish within Burton and Holme — surveyed as existing and drawn to the detail Westmorland and Furness Council's conservation officer needs.

Lupton

Listed building consent drawings for Lupton — civil parish within Burton and Holme — surveyed as existing and drawn to the detail Westmorland and Furness Council's conservation officer needs.

Mansergh

Listed building consent drawings for Mansergh — civil parish within Burton and Holme — surveyed as existing and drawn to the detail Westmorland and Furness Council's conservation officer needs.

Burton-in-Kendal

Listed building consent drawings for Burton-in-Kendal — civil parish within Burton and Holme — surveyed as existing and drawn to the detail Westmorland and Furness Council's conservation officer needs.

Listed building consent or planning permission in Burton and Holme?

They are separate consents with different tests, and many projects need both.

ConsentWhat it coversFeeConsequence of proceeding without it
Listed building consentWorks affecting special interest, internal and externalNoneCriminal offence under section 9 of the 1990 Act
Planning permissionDevelopment — extensions, outbuildings, use changesPayableEnforcement action; may become immune after 10 years
Conservation area consent contextDemolition and character in a designated areaVariesEnforcement; prosecution for unauthorised demolition
Building regulationsStructure, fire, insulation, ventilationPayableEnforcement notice; problems on sale

Sources: Planning (Listed Buildings and Conservation Areas) Act 1990, sections 7, 9 and 16(2); Town and Country Planning Act 1990.

Four steps to consent on a Burton and Holme listed building

A process built around what a conservation officer actually assesses.

  1. 1

    Free initial check

    Send us the address and the listing entry. We confirm grade, what the listing covers, whether curtilage structures are caught, and how Westmorland and Furness Council has treated comparable schemes.

  2. 2

    Measured record of the building

    We survey as existing in real detail — plans, elevations, sections and the features that carry the significance — because a proposal cannot be assessed against a record that does not exist.

  3. 3

    Proposal & heritage statement

    We draw the proposal in matching detail and write the heritage statement that identifies significance, impact and justification in the terms section 16(2) requires.

  4. 4

    Submission & follow-through

    We submit to Westmorland and Furness Council, engage with the conservation officer, and revise the drawings free until the decision is issued.

Frequently asked questions

Do I need listed building consent for internal work in Burton and Holme?

Frequently, yes. Listing covers the whole building, so removing a partition, altering a staircase, replacing joinery or re-plastering historic surfaces can all require consent from Westmorland and Furness Council. There is no internal exemption and no size threshold. The safe route is to establish what is significant before work is designed, which is what the measured survey is for. This applies to your Burton and Holme address specifically.

What happens if work is done without listed building consent in Burton and Holme?

Carrying out unauthorised works to a listed building is a criminal offence under section 9 of the Planning (Listed Buildings and Conservation Areas) Act 1990, and it does not become lawful with the passage of time the way some planning breaches do. Westmorland and Furness Council can require reinstatement. Where work has already happened, an application for retrospective consent is usually the right first step, and we can advise on it. This applies to your Burton and Holme address specifically.

Is there a fee for listed building consent in Burton and Holme?

No. Listed building consent applications carry no application fee, which sometimes leads owners to assume the process is lighter than a planning application. It is not — the evidence expected is greater, because the decision rests on the effect on special interest rather than on amenity, and an under-documented submission is the most common cause of delay. This applies to your Burton and Holme address specifically. Westmorland and Furness Council is the decision-maker.

Do I need planning permission as well as listed building consent in Burton and Holme?

If the work is also development — an extension, an outbuilding, a change of use — then yes, and the two applications run in parallel to Westmorland and Furness Council. Internal alterations usually need only listed building consent. Where both are required we prepare them as one coordinated set, because inconsistencies between the two submissions are a recurring reason for delay. This applies to your Burton and Holme address specifically.

Can I replace the windows in a listed building in Burton and Holme?

Sometimes, but rarely with modern units. Historic windows are often the single most significant surviving feature, and replacement is judged on the condition of the existing joinery and the accuracy of what replaces it — glazing bar profile, glass type, opening method and reveal depth all matter. Repair and secondary glazing are usually the route that gains consent, particularly inside designated areas such as Burton. This applies to your Burton and Holme address specifically. Westmorland and Furness Council is the decision-maker.

How long does listed building consent take in Burton and Holme?

The statutory target is eight weeks from validation for most applications, and thirteen for larger schemes. In practice the timetable is set by how complete the submission is: a conservation officer who has to ask what the existing fabric looks like will take longer than one who can see it. We submit a record that answers those questions upfront. This applies to your Burton and Holme address specifically. Westmorland and Furness Council is the decision-maker.

How much do listed building drawings in Burton and Holme cost?

We quote each Burton and Holme listed project individually, because the survey effort depends entirely on the building's complexity and how much of the fabric the work touches, and send a fixed, no-obligation quote within one working day. It covers survey, drawings and heritage statement, with free revisions until Westmorland and Furness Council decides. Call 020 7864 7245 to start.

Planning approval report

Know your approval odds before you spend a penny on drawings

Answer five quick questions and get a free planning score for your exact address — instantly. Then, if you want the full picture, unlock the detailed analysis: your council's live approval rates, local precedents, constraints on your street and a step-by-step route to permission.

Listed building consent drawings across Westmorland and Furness

Same fixed quotes, same fast drawings — wherever your project is.

Other planning services in Burton and Holme