Hip-to-gable drawings for Bunny semis and end-terraces — building the sloping hipped end up into a flat gable wall to unlock the full width of the roof, drawn to Rushcliffe Borough Council's guidance, delivered in days and revised free until your decision, with a free approval-odds check first.
Rushcliffe Borough Council granted 95% of the householder planning decisions it made in its latest published year — 8 points above the 87% England-wide householder average. Bunny contains Bradmore, Bunny, Costock conservation areas (Bradmore designated 1994), so materials, fenestration and roof form are assessed against the appraisal, which is where a policy-literate drawing pack earns its keep. Its dominant Victorian (1837–1901), interwar (1918–1939) and postwar (1945–1970) housing stock sets the design brief on most streets.
Class A and Class B set the thresholds — a rear dormer to 40m³ on a terrace or 50m³ on a semi or detached, and a single-storey rear extension to 3m on a terrace or 4m on a detached house — beyond which Rushcliffe Borough Council needs a full application. In conservation areas such as Bradmore, Bunny and Costock those rights are removed, so we confirm your exact address before a line is drawn. A validated householder application in Bunny is determined against an 8-week statutory target.
Bradmore (conservation area designated in 1994), Bunny (designated conservation area), Costock (conservation area designated in 1990), Wysall (conservation area designated in 1990), Rempstone (civil parish within Bunny), Thorpe in the Glebe (civil parish within Bunny), Willoughby on the Wolds (civil parish within Bunny), Bradmore (civil parish within Bunny), Wysall (civil parish within Bunny) and Costock (civil parish within Bunny) — these are the Bunny pockets our drawings cover most. Heritage designations here include Bradmore, Bunny, Costock and Wysall. Rushcliffe Borough Council weighs each proposal against the adopted Rushcliffe local plan and Rushcliffe Borough Council's design guidance for householder work, where the 1,120 homes here are 21% pre-1900, 15% 1930-1939, 11% 1965-1972, which is what sets the realistic roof and rear-projection options. On roofs the borough is steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and hipped roofs with shallow pitches typical of 1930s building, over Victorian and earlier houses (21% of 1,120 homes), 1930s semi-detached and detached houses (15%) and late-1960s and early-1970s houses (11%).
Heritage designation is the single biggest variable in Bunny, and it is address-specific: Bradmore (conservation area designated in 1994), Bunny (designated conservation area), Costock (conservation area designated in 1990) and Wysall (conservation area designated in 1990). Inside those boundaries permitted development is curtailed and Rushcliffe Borough Council assesses materials, window detail and roof form against the area's own appraisal, so a scheme that would be waved through two streets away can need a full application here.
Beyond the designated areas, Bunny takes in Rempstone, Thorpe in the Glebe, Willoughby on the Wolds, Bradmore, Wysall and Costock. No Article 4 direction is recorded for Rushcliffe Borough Council, but Bunny's 4 conservation areas still limit permitted development on those streets.
On stock, Bunny is Victorian and earlier houses (21% of 1,120 homes), 1930s semi-detached and detached houses (15%) and late-1960s and early-1970s houses (11%) — which is why steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and hipped roofs with shallow pitches typical of 1930s building govern what a loft or rear projection can realistically be. Rushcliffe Borough Council decided 476 householder applications in the latest published year and granted 95%, with 51% issued inside the eight-week target. We work from the council's own published record.
The full build-period split for Bunny runs pre-1900 21% (240 homes), 1900-1918 3% (30 homes), 1919-1929 4% (40 homes), 1930-1939 15% (170 homes), 1945-1954 4% (40 homes), 1955-1964 9% (100 homes), 1965-1972 11% (120 homes), 1973-1982 6% (70 homes), 1983-1992 4% (50 homes), 1993-1999 5% (60 homes) and 2000-2008 10% (110 homes). That distribution is why pre-1900 detailing dominates the drawings here, and it is measured from council-tax records rather than assumed from the street name.
Rushcliffe Borough Council also decides for Bingham North, Cotgrave, Cranmer, Cropwell, East Bridgford, Gotham, Keyworth & Wolds and Leake, so a decision in Bunny sits inside a wider pattern of decisions we track across the same authority — useful when an officer cites a precedent from the next area over.
Published figures for Bunny and Rushcliffe Borough Council. These are the numbers that decide what is realistic on your street, so we work from them rather than from national averages.
| Measure | Bunny |
|---|---|
| Dwellings recorded | 1,120 |
| Built pre-1900 | 240 (21%) |
| Built 1900-1918 | 30 (3%) |
| Built 1919-1929 | 40 (4%) |
| Built 1930-1939 | 170 (15%) |
| Built 1945-1954 | 40 (4%) |
| Built 1955-1964 | 100 (9%) |
| Built 1965-1972 | 120 (11%) |
| Built 1973-1982 | 70 (6%) |
| Built 1983-1992 | 50 (4%) |
| Built 1993-1999 | 60 (5%) |
| Built 2000-2008 | 110 (10%) |
| Built before 1919 | 24% |
| Built 1919–1939 | 19% |
| Built 1945–2008 | 49% |
| Conservation areas in Bunny | 4 (Bradmore, Bunny…) |
| Conservation areas district-wide | 32 |
| Article 4 directions recorded | 0 |
| Householder applications decided | 476 |
| Householder applications granted | 95% |
| Decided within 8 weeks | 51% |
Dwelling stock from VOA council-tax data at 31 March 2025; conservation-area and Article 4 counts from planning.data.gov.uk (MHCLG); decision figures are Rushcliffe Borough Council's own, from MHCLG live table PS2 for the year to 31 March 2026.
The hip-to-gable is the semi's loft, and Bunny has the stock that needs it — the borough runs to Victorian and earlier houses (21% of 1,120 homes), 1930s semi-detached and detached houses (15%) and late-1960s and early-1970s houses (11%), and wherever the roof is hipped it wastes the triangle of space where the slope cuts in at the side. Build that hip up into a gable wall and the loft gains full-height room right across the width, usually with a rear dormer behind it. Rushcliffe Borough Council judges the scheme against the adopted Rushcliffe local plan and Rushcliffe Borough Council's design guidance for householder work, and because the gable is a side elevation it is read against the neighbouring house first.
That neighbour relationship is the drawing's job. We build the gable to the original ridge line, match the brick or render and the verge detail to the host, and where the house is one of a mirrored pair we show the new gable against the neighbour's retained hip so the officer can weigh the balance. Bunny contains Bradmore, Bunny, Costock conservation areas (Bradmore designated 1994), so materials, fenestration and roof form are assessed against the appraisal, and on a paired roof that is precisely the test a hip-to-gable has to pass.
Where Bunny's streets are designated — Bradmore, Bunny, Costock and Wysall among them — a hip-to-gable is scrutinised hard, because losing a hip changes the roofscape the area is protected for. No Article 4 direction is recorded for Rushcliffe Borough Council, but Bunny's 4 conservation areas still limit permitted development on those streets. We check the designation before the gable is drawn.
A hip-to-gable in Bunny is not permitted development — extending the roof up and out over the hip takes it past what Class B allows — so it needs a full application to Rushcliffe Borough Council. These are the points the council weighs:
We draw the new gable to the existing ridge, the verge and materials matched to the host, and the balance with the neighbour's retained hip — the side-elevation relationships Rushcliffe Borough Council's officers check first — and submit a validation-complete householder application, usually with the rear dormer on the same drawings.
Below is Rushcliffe Borough Council's real householder decision record, drawn from official planning statistics and refreshed as new data lands. Rushcliffe Borough Council granted 95% of its householder applications in the year to 31 March 2026, and Bradmore shapes what is approved here. A hip-to-gable turns on side-elevation bulk and the balance of the pair, so a pack that draws the gable against the neighbour is decided faster and refused less often than a DIY submission.
Source: MHCLG planning application statistics (householder decisions, England, 1 April 2025 - 31 March 2026). Compare every borough on our London approval-rate league table.
Tell us about your project and get a fixed, no-obligation quote back within one working day. If you don't need planning permission at all, we'll tell you that too — for free.
Across Bradmore, Bunny and Costock, the hip-to-gable that goes through is the restrained one: the gable built to the original ridge rather than above it, materials matched so the extended end reads as part of the house, and — on a pair — the new wall sitting comfortably beside the neighbour's hip rather than overwhelming it. On the borough's victorian and earlier houses (21% of 1,120 homes), squaring one or both hips is what makes the whole loft usable, which is why it is nearly always drawn with a rear dormer behind.
The 1,120 homes here are 21% pre-1900, 15% 1930-1939, 11% 1965-1972, which is what sets the realistic roof and rear-projection options. We hold the gable to the ridge, detail the verge and the flank window to sit quietly, and present the gable and dormer as one roof alteration — so Rushcliffe Borough Council assesses a single coherent change to the roof rather than two competing ones.
We draw hip-to-gable lofts on the semi-detached and end-of-terrace streets across the borough. A few of the neighbourhoods where Bunny hip-to-gables come up most often:
Hip-to-gable loft drawings for Bradmore's conservation area designated in 1994 — ridge-matched, pair-balanced and drawn to Rushcliffe Borough Council's guidance.
Hip-to-gable loft drawings for Bunny's designated conservation area — ridge-matched, pair-balanced and drawn to Rushcliffe Borough Council's guidance.
Hip-to-gable loft drawings for Costock's conservation area designated in 1990 — ridge-matched, pair-balanced and drawn to Rushcliffe Borough Council's guidance.
Hip-to-gable loft drawings for Wysall's conservation area designated in 1990 — ridge-matched, pair-balanced and drawn to Rushcliffe Borough Council's guidance.
Hip-to-gable loft drawings for Rempstone's civil parish within Bunny — ridge-matched, pair-balanced and drawn to Rushcliffe Borough Council's guidance.
Hip-to-gable loft drawings for Thorpe in the Glebe's civil parish within Bunny — ridge-matched, pair-balanced and drawn to Rushcliffe Borough Council's guidance.
A hip-to-gable only applies where the roof is hipped — and what it gains depends on the house. This is how the cases compare.
| Roof / house type | Hip-to-gable route | What it gains | What Rushcliffe Borough Council checks |
|---|---|---|---|
| Hipped semi-detached | Full application, one gable | Full-width loft on the hipped side | Balance with the paired neighbour |
| Hipped end-terrace | Full application, one gable | Squares off the exposed end | Side elevation and street rhythm |
| Hipped detached | Full application, one or both ends | Loft across the whole roof | Bulk and the wider roofscape |
| Already gabled roof | Not needed — dormer only | Space via a rear dormer instead | Dormer volume and set-back |
In conservation areas such as Bradmore and Bunny, the loss of a hip is resisted and a hip-to-gable is assessed on its effect on the protected roofscape.
A fixed process built around how Rushcliffe Borough Council validates and decides hip-to-gable applications — most drawings are submission-ready within seven days of survey.
Send us your Bunny postcode and whether your roof is hipped one or both ends. We confirm your conservation and Article 4 status and score your odds against live Rushcliffe Borough Council decisions.
We measure the ridge and eaves, the hip geometry and — on a pair — the neighbour's roof, so the new gable can be drawn to the original ridge and balanced against the adjoining house.
Chartered designers develop the gable and its rear dormer to your brief, drawn to Rushcliffe Borough Council's roof-alteration guidance with the side elevation and neighbour relationship resolved on the page.
We submit the householder application, manage validation and case-officer queries, and revise the drawings free until Rushcliffe Borough Council issues its decision.
Yes. A hip-to-gable rebuilds the sloping hipped end of the roof as a vertical gable, and because that extends the roof it falls outside permitted development — so it always needs a full householder application to Rushcliffe Borough Council, whether or not your street is designated. It is usually submitted together with a rear dormer as a single roof-alteration application. This applies to your Bunny address specifically.
It replaces the roof's sloping hipped end with a flat gable wall built up to the ridge, turning the wasted triangle where the slope cuts in into full-height loft space across the width of the house. Bunny's hipped semis and end-terraces suit it especially well, and it is nearly always paired with a rear dormer to open up the back of the roof too. Rushcliffe Borough Council is the decision-maker.
Yes, and a matching pair often reads better to Rushcliffe Borough Council than a single gable on one side, because it keeps the two houses balanced. Where only one owner converts, we draw the new gable carefully against the neighbour's retained hip so the officer can see the pair still works. The balance of the pair is one of the main things the council weighs. This applies to your Bunny address specifically.
Almost always. The gable opens up the side of the roof and a rear dormer opens up the back, and together they make the whole loft usable — so in Bunny the two are typically drawn and submitted as one application to Rushcliffe Borough Council. Presenting them together means the council assesses a single coherent change to the roof rather than two separate alterations.
Usually, on a semi or end-terrace. The gable is built up off the flank, and the loft steelwork often bears on the party wall, so the Party Wall etc. Act applies and notice must be served before work starts — separately from Rushcliffe Borough Council's planning decision. We detail the junction on the drawings and flag the notice early so a surveyor can be appointed without delay. This applies to your Bunny address specifically.
We price each Bunny hip-to-gable individually, because the roof geometry and whether it is one gable or two vary house to house, and send a fixed, no-obligation quote within one working day. It covers the full drawing pack — usually gable plus rear dormer — with free revisions until Rushcliffe Borough Council approves. Call 020 7864 7245 to start.
Answer five quick questions and get a free planning score for your exact address — instantly. Then, if you want the full picture, unlock the detailed analysis: your council's live approval rates, local precedents, constraints on your street and a step-by-step route to permission.
Same fixed quotes, same fast drawings — wherever your project is.