
Hip-to-gable drawings for Basingstoke and Deane semis and end-terraces — building the sloping hipped end up into a flat gable wall to unlock the full width of the roof, drawn to Basingstoke and Deane Borough Council's guidance, delivered in days and revised free until your decision, with a free approval-odds check first.
Basingstoke and Deane Borough Council granted 96% of the householder planning decisions it made in its latest published year — 9 points above the 87% England-wide householder average. Basingstoke and Deane contains Ashmansworth, Basingstoke Canal, Bradley conservation areas (Ashmansworth designated 1989), so materials, fenestration and roof form are assessed against the appraisal, which is where a policy-literate drawing pack earns its keep. Its dominant Victorian (1837–1901) and postwar (1945–1970) housing stock sets the design brief on most streets.
Class A and Class B set the thresholds — a rear dormer to 40m³ on a terrace or 50m³ on a semi or detached, and a single-storey rear extension to 3m on a terrace or 4m on a detached house — beyond which Basingstoke and Deane Borough Council needs a full application. Basingstoke and Deane carries at least one Article 4 direction, and conservation areas including Ashmansworth, Basingstoke Canal and Bradley remove those rights outright, so we confirm your exact address before a line is drawn. A validated householder application in Basingstoke and Deane is determined against an 8-week statutory target.
Ashmansworth (conservation area designated in 1989), Basingstoke Canal (conservation area designated in 1977), Bradley (conservation area designated in 1992), Bramley and Bramley Green (conservation area designated in 1983), Brown and Chilton Candover (conservation area designated in 1981), Church Oakley (conservation area designated in 1976), Church Road, Tadley (conservation area designated in 1982), Cliddesden (conservation area designated in 1981), Basing & Upton Grey (ward of Basingstoke and Deane), Bramley (ward of Basingstoke and Deane), Evingar (ward of Basingstoke and Deane), Oakley & The Candovers (ward of Basingstoke and Deane), Tadley & Pamber (ward of Basingstoke and Deane) and Winklebury & Manydown (ward of Basingstoke and Deane) — these are the Basingstoke and Deane pockets our drawings cover most. Heritage designations here include Ashmansworth, Basingstoke Canal, Bradley, Bramley and Bramley Green, Brown and Chilton Candover, Church Oakley, Church Road, Tadley and Cliddesden. Basingstoke and Deane Borough Council weighs each proposal against the adopted Basingstoke and Deane local plan and Basingstoke and Deane Borough Council's design guidance for householder work, where the 25,000 homes here are 17% 1973-1982, 14% 1965-1972, 7% pre-1900, which is what sets the realistic roof and rear-projection options. On roofs the borough is shallow trussed roofs typical of 1970s building and shallow-pitched roofs and integral garages typical of that period's building, over 1970s and early-1980s houses (17% of 25,000 homes), late-1960s and early-1970s houses (14%) and Victorian and earlier houses (7%).
Heritage designation is the single biggest variable in Basingstoke and Deane, and it is address-specific: Ashmansworth (conservation area designated in 1989), Basingstoke Canal (conservation area designated in 1977), Bradley (conservation area designated in 1992), Bramley and Bramley Green (conservation area designated in 1983), Brown and Chilton Candover (conservation area designated in 1981), Church Oakley (conservation area designated in 1976), Church Road, Tadley (conservation area designated in 1982) and Cliddesden (conservation area designated in 1981). Inside those boundaries permitted development is curtailed and Basingstoke and Deane Borough Council assesses materials, window detail and roof form against the area's own appraisal, so a scheme that would be waved through two streets away can need a full application here.
Beyond the designated areas, Basingstoke and Deane takes in Basing & Upton Grey, Bramley, Evingar, Oakley & The Candovers, Tadley & Pamber and Winklebury & Manydown. Basingstoke and Deane Borough Council has 3 recorded Article 4 directions — check the address before assuming PD applies in the district.
On stock, Basingstoke and Deane is 1970s and early-1980s houses (17% of 25,000 homes), late-1960s and early-1970s houses (14%) and Victorian and earlier houses (7%) — which is why shallow trussed roofs typical of 1970s building and shallow-pitched roofs and integral garages typical of that period's building govern what a loft or rear projection can realistically be. Basingstoke and Deane Borough Council decided 616 householder applications in the latest published year and granted 96%, with 59% issued inside the eight-week target. We work from the council's own published record.
The full build-period split for Basingstoke and Deane runs pre-1900 3% (190 homes), 1900-1918 0% (30 homes), 1919-1929 0% (10 homes), 1930-1939 6% (350 homes), 1945-1954 3% (170 homes), 1955-1964 30% (1,850 homes), 1965-1972 33% (1,990 homes), 1973-1982 4% (260 homes), 1983-1992 5% (310 homes), 1993-1999 4% (220 homes) and 2000-2008 3% (170 homes). That distribution is why pre-1900 detailing dominates the drawings here, and it is measured from council-tax records rather than assumed from the street name.
Basingstoke and Deane Borough Council also decides for Basing & Upton Grey, Bramley, Evingar, Oakley & The Candovers, Tadley & Pamber and Winklebury & Manydown, so a decision in Basingstoke and Deane sits inside a wider pattern of decisions we track across the same authority — useful when an officer cites a precedent from the next area over.
The Article 4 directions recorded for this council include Basing View, Basingstoke Town and Chineham and the surrounding villages of Old Basing, Oakley and Sherborne St John. and Chineham Business Park and Hampshire International Business Park. Each removes a specific permitted-development right inside its own boundary, which is why the check is done on the address rather than on the town.
Published figures for Basingstoke and Deane and Basingstoke and Deane Borough Council. These are the numbers that decide what is realistic on your street, so we work from them rather than from national averages.
| Measure | Basingstoke and Deane |
|---|---|
| Dwellings recorded | 25,000 |
| Built pre-1900 | 190 (3%) |
| Built 1900-1918 | 30 (0%) |
| Built 1919-1929 | 10 (0%) |
| Built 1930-1939 | 350 (6%) |
| Built 1945-1954 | 170 (3%) |
| Built 1955-1964 | 1,850 (30%) |
| Built 1965-1972 | 1,990 (33%) |
| Built 1973-1982 | 260 (4%) |
| Built 1983-1992 | 310 (5%) |
| Built 1993-1999 | 220 (4%) |
| Built 2000-2008 | 170 (3%) |
| Built before 1919 | 12% |
| Built 1919–1939 | 5% |
| Built 1945–2008 | 67% |
| Conservation areas in Basingstoke and Deane | 8 (Ashmansworth, Basingstoke Canal…) |
| Conservation areas district-wide | 43 |
| Article 4 directions recorded | 3 |
| Householder applications decided | 616 |
| Householder applications granted | 96% |
| Decided within 8 weeks | 59% |
Dwelling stock from VOA council-tax data at 31 March 2025; conservation-area and Article 4 counts from planning.data.gov.uk (MHCLG); decision figures are Basingstoke and Deane Borough Council's own, from MHCLG live table PS2 for the year to 31 March 2026.
The hip-to-gable is the semi's loft, and Basingstoke and Deane has the stock that needs it — the borough runs to 1970s and early-1980s houses (17% of 25,000 homes), late-1960s and early-1970s houses (14%) and Victorian and earlier houses (7%), and wherever the roof is hipped it wastes the triangle of space where the slope cuts in at the side. Build that hip up into a gable wall and the loft gains full-height room right across the width, usually with a rear dormer behind it. Basingstoke and Deane Borough Council judges the scheme against the adopted Basingstoke and Deane local plan and Basingstoke and Deane Borough Council's design guidance for householder work, and because the gable is a side elevation it is read against the neighbouring house first.
That neighbour relationship is the drawing's job. We build the gable to the original ridge line, match the brick or render and the verge detail to the host, and where the house is one of a mirrored pair we show the new gable against the neighbour's retained hip so the officer can weigh the balance. Basingstoke and Deane contains Ashmansworth, Basingstoke Canal, Bradley conservation areas (Ashmansworth designated 1989), so materials, fenestration and roof form are assessed against the appraisal, and on a paired roof that is precisely the test a hip-to-gable has to pass.
Where Basingstoke and Deane's streets are designated — Ashmansworth, Basingstoke Canal, Bradley, Bramley and Bramley Green, Brown and Chilton Candover, Church Oakley, Church Road, Tadley and Cliddesden among them — a hip-to-gable is scrutinised hard, because losing a hip changes the roofscape the area is protected for. Basingstoke and Deane Borough Council has 3 recorded Article 4 directions — check the address before assuming PD applies in the district. We check the designation before the gable is drawn.

A hip-to-gable in Basingstoke and Deane is not permitted development — extending the roof up and out over the hip takes it past what Class B allows — so it needs a full application to Basingstoke and Deane Borough Council. These are the points the council weighs:
We draw the new gable to the existing ridge, the verge and materials matched to the host, and the balance with the neighbour's retained hip — the side-elevation relationships Basingstoke and Deane Borough Council's officers check first — and submit a validation-complete householder application, usually with the rear dormer on the same drawings.
Below is Basingstoke and Deane Borough Council's real householder decision record, drawn from official planning statistics and refreshed as new data lands. Basingstoke and Deane Borough Council granted 96% of 616 householder decisions in the year to 31 March 2026, 59% of them inside eight weeks. A hip-to-gable turns on side-elevation bulk and the balance of the pair, so a pack that draws the gable against the neighbour is decided faster and refused less often than a DIY submission.
Source: MHCLG planning application statistics (householder decisions, England, 1 April 2025 - 31 March 2026). Compare every borough on our London approval-rate league table.
Tell us about your project and get a fixed, no-obligation quote back within one working day. If you don't need planning permission at all, we'll tell you that too — for free.
Across Ashmansworth, Basingstoke Canal and Bradley, the hip-to-gable that goes through is the restrained one: the gable built to the original ridge rather than above it, materials matched so the extended end reads as part of the house, and — on a pair — the new wall sitting comfortably beside the neighbour's hip rather than overwhelming it. On the borough's 1970s and early-1980s houses (17% of 25,000 homes), squaring one or both hips is what makes the whole loft usable, which is why it is nearly always drawn with a rear dormer behind.
The 25,000 homes here are 17% 1973-1982, 14% 1965-1972, 7% pre-1900, which is what sets the realistic roof and rear-projection options. We hold the gable to the ridge, detail the verge and the flank window to sit quietly, and present the gable and dormer as one roof alteration — so Basingstoke and Deane Borough Council assesses a single coherent change to the roof rather than two competing ones.

We draw hip-to-gable lofts on the semi-detached and end-of-terrace streets across the borough. A few of the neighbourhoods where Basingstoke and Deane hip-to-gables come up most often:
Hip-to-gable loft drawings for Ashmansworth's conservation area designated in 1989 — ridge-matched, pair-balanced and drawn to Basingstoke and Deane Borough Council's guidance.
Hip-to-gable loft drawings for Basingstoke Canal's conservation area designated in 1977 — ridge-matched, pair-balanced and drawn to Basingstoke and Deane Borough Council's guidance.
Hip-to-gable loft drawings for Bradley's conservation area designated in 1992 — ridge-matched, pair-balanced and drawn to Basingstoke and Deane Borough Council's guidance.
Hip-to-gable loft drawings for Bramley and Bramley Green's conservation area designated in 1983 — ridge-matched, pair-balanced and drawn to Basingstoke and Deane Borough Council's guidance.
Hip-to-gable loft drawings for Brown and Chilton Candover's conservation area designated in 1981 — ridge-matched, pair-balanced and drawn to Basingstoke and Deane Borough Council's guidance.
Hip-to-gable loft drawings for Church Oakley's conservation area designated in 1976 — ridge-matched, pair-balanced and drawn to Basingstoke and Deane Borough Council's guidance.
A hip-to-gable only applies where the roof is hipped — and what it gains depends on the house. This is how the cases compare.
| Roof / house type | Hip-to-gable route | What it gains | What Basingstoke and Deane Borough Council checks |
|---|---|---|---|
| Hipped semi-detached | Full application, one gable | Full-width loft on the hipped side | Balance with the paired neighbour |
| Hipped end-terrace | Full application, one gable | Squares off the exposed end | Side elevation and street rhythm |
| Hipped detached | Full application, one or both ends | Loft across the whole roof | Bulk and the wider roofscape |
| Already gabled roof | Not needed — dormer only | Space via a rear dormer instead | Dormer volume and set-back |
In conservation areas such as Ashmansworth and Basingstoke Canal, the loss of a hip is resisted and a hip-to-gable is assessed on its effect on the protected roofscape.
A fixed process built around how Basingstoke and Deane Borough Council validates and decides hip-to-gable applications — most drawings are submission-ready within seven days of survey.
Send us your Basingstoke and Deane postcode and whether your roof is hipped one or both ends. We confirm your conservation and Article 4 status and score your odds against live Basingstoke and Deane Borough Council decisions.
We measure the ridge and eaves, the hip geometry and — on a pair — the neighbour's roof, so the new gable can be drawn to the original ridge and balanced against the adjoining house.
Chartered designers develop the gable and its rear dormer to your brief, drawn to Basingstoke and Deane Borough Council's roof-alteration guidance with the side elevation and neighbour relationship resolved on the page.
We submit the householder application, manage validation and case-officer queries, and revise the drawings free until Basingstoke and Deane Borough Council issues its decision.
Yes. A hip-to-gable rebuilds the sloping hipped end of the roof as a vertical gable, and because that extends the roof it falls outside permitted development — so it always needs a full householder application to Basingstoke and Deane Borough Council, whether or not your street is designated. It is usually submitted together with a rear dormer as a single roof-alteration application.
It replaces the roof's sloping hipped end with a flat gable wall built up to the ridge, turning the wasted triangle where the slope cuts in into full-height loft space across the width of the house. Basingstoke and Deane's hipped semis and end-terraces suit it especially well, and it is nearly always paired with a rear dormer to open up the back of the roof too. Basingstoke and Deane Borough Council is the decision-maker.
Yes, and a matching pair often reads better to Basingstoke and Deane Borough Council than a single gable on one side, because it keeps the two houses balanced. Where only one owner converts, we draw the new gable carefully against the neighbour's retained hip so the officer can see the pair still works. The balance of the pair is one of the main things the council weighs.
Almost always. The gable opens up the side of the roof and a rear dormer opens up the back, and together they make the whole loft usable — so in Basingstoke and Deane the two are typically drawn and submitted as one application to Basingstoke and Deane Borough Council. Presenting them together means the council assesses a single coherent change to the roof rather than two separate alterations.
Usually, on a semi or end-terrace. The gable is built up off the flank, and the loft steelwork often bears on the party wall, so the Party Wall etc. Act applies and notice must be served before work starts — separately from Basingstoke and Deane Borough Council's planning decision. We detail the junction on the drawings and flag the notice early so a surveyor can be appointed without delay.
We price each Basingstoke and Deane hip-to-gable individually, because the roof geometry and whether it is one gable or two vary house to house, and send a fixed, no-obligation quote within one working day. It covers the full drawing pack — usually gable plus rear dormer — with free revisions until Basingstoke and Deane Borough Council approves. Call 020 7864 7245 to start.
Answer five quick questions and get a free planning score for your exact address — instantly. Then, if you want the full picture, unlock the detailed analysis: your council's live approval rates, local precedents, constraints on your street and a step-by-step route to permission.
Same fixed quotes, same fast drawings — wherever your project is.