Rear dormer drawings for Mere roofs — the box across the back slope that turns a low attic into a full-height room, drawn to Wiltshire Council's guidance and the volume limits, delivered in days and revised free until your decision, with a free approval-odds check first.
Wiltshire Council granted 96% of the householder planning decisions it made in its latest published year — 9 points above the 87% England-wide householder average. Mere contains MERE, STOURTON, ZEALS conservation areas (MERE designated 1973), so materials, fenestration and roof form are assessed against the appraisal, which is where a policy-literate drawing pack earns its keep. Its dominant Victorian (1837–1901) and postwar (1945–1970) housing stock sets the design brief on most streets.
Before permission is required, Class B allows 40m³ of added loft volume on a terrace and 50m³ on a semi or detached house, and Class A allows a 3m single-storey rear extension on a terrace or 4m on a detached house. Mere carries at least one Article 4 direction, and conservation areas including MERE, STOURTON and ZEALS remove those rights outright, so we confirm your exact address before a line is drawn. A validated householder application in Mere is determined against an 8-week statutory target.
MERE (conservation area designated in 1973), STOURTON (conservation area designated in 1975), ZEALS (conservation area designated in 1986), Kilmington (civil parish within Mere), West Knoyle (civil parish within Mere), Zeals (civil parish within Mere) and Stourton with Gasper (civil parish within Mere) — these are the Mere pockets our drawings cover most. Heritage designations here include MERE, STOURTON and ZEALS. Wiltshire Council weighs each proposal against Wiltshire Council's development plan and the design policies it applies to householder applications, where the 2,370 homes here are 33% pre-1900, 11% 1993-1999, 10% 1965-1972, which is what sets the realistic roof and rear-projection options. On roofs the borough is steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and trussed-rafter roofs typical of 1990s building, over Victorian and earlier houses (33% of 2,370 homes), 1990s estate houses (11%) and late-1960s and early-1970s houses (10%).
What is permitted in Mere turns on designation first, so that is where we start: MERE (conservation area designated in 1973), STOURTON (conservation area designated in 1975) and ZEALS (conservation area designated in 1986). Inside those boundaries permitted development is curtailed and Wiltshire Council assesses materials, window detail and roof form against the area's own appraisal, so a scheme that would be waved through two streets away can need a full application here.
Beyond the designated areas, Mere takes in Kilmington, West Knoyle, Zeals and Stourton with Gasper. Wiltshire Council has 48 recorded Article 4 directions, removing permitted development for rear and side extensions and other roof alterations, including rooflights — check the address before assuming PD applies in Mere.
On stock, Mere is Victorian and earlier houses (33% of 2,370 homes), 1990s estate houses (11%) and late-1960s and early-1970s houses (10%) — which is why steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and trussed-rafter roofs typical of 1990s building govern what a loft or rear projection can realistically be. Wiltshire Council decided 1,779 householder applications in the latest published year and granted 96%, with 53% issued inside the eight-week target. We draw to that record rather than to a national average.
The full build-period split for Mere runs pre-1900 33% (790 homes), 1900-1918 3% (60 homes), 1919-1929 2% (40 homes), 1930-1939 3% (70 homes), 1945-1954 4% (100 homes), 1955-1964 5% (130 homes), 1965-1972 10% (230 homes), 1973-1982 8% (180 homes), 1983-1992 4% (100 homes), 1993-1999 11% (250 homes) and 2000-2008 8% (200 homes). That distribution is why pre-1900 detailing dominates the drawings here, and it is measured from council-tax records rather than assumed from the street name.
Wiltshire Council also decides for Aldbourne & Ramsbury, Amesbury West, Avon Valley, Box & Colerne, By Brook, Corsham Ladbrook, Corsham Pickwick and Corsham Without, so a decision in Mere sits inside a wider pattern of decisions we track across the same authority — useful when an officer cites a precedent from the next area over.
The Article 4 directions recorded for this council include Ashley, Avebury, Baydon 1 and Baydon 2. Each removes a specific permitted-development right inside its own boundary, which is why the check is done on the address rather than on the town.
Published figures for Mere and Wiltshire Council. These are the numbers that decide what is realistic on your street, so we work from them rather than from national averages.
| Measure | Mere |
|---|---|
| Dwellings recorded | 2,370 |
| Built pre-1900 | 790 (33%) |
| Built 1900-1918 | 60 (3%) |
| Built 1919-1929 | 40 (2%) |
| Built 1930-1939 | 70 (3%) |
| Built 1945-1954 | 100 (4%) |
| Built 1955-1964 | 130 (5%) |
| Built 1965-1972 | 230 (10%) |
| Built 1973-1982 | 180 (8%) |
| Built 1983-1992 | 100 (4%) |
| Built 1993-1999 | 250 (11%) |
| Built 2000-2008 | 200 (8%) |
| Built before 1919 | 36% |
| Built 1919–1939 | 5% |
| Built 1945–2008 | 50% |
| Conservation areas in Mere | 3 (MERE, STOURTON…) |
| Conservation areas district-wide | 245 |
| Article 4 directions recorded | 48 |
| Householder applications decided | 1,779 |
| Householder applications granted | 96% |
| Decided within 8 weeks | 53% |
Dwelling stock from VOA council-tax data at 31 March 2025; conservation-area and Article 4 counts from planning.data.gov.uk (MHCLG); decision figures are Wiltshire Council's own, from MHCLG live table PS2 for the year to 31 March 2026.
The box dormer is the workhorse loft, and most of Mere is built for it — the borough runs to Victorian and earlier houses (33% of 2,370 homes), 1990s estate houses (11%) and late-1960s and early-1970s houses (10%) under steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and trussed-rafter roofs typical of 1990s building, and a flat-roofed box across the rear slope is the cheapest cubic metre of full-height space those roofs give up. Wiltshire Council tests the dormer against Wiltshire Council's development plan and the design policies it applies to householder applications, and because permitted development turns on a number, the volume you propose against the volume you have left is the first thing an officer or a certificate checks.
That is why the arithmetic goes on the drawings. We calculate the box against the 40- or 50-cubic-metre allowance, count any earlier roof enlargement into the total, hold the flat roof below the ridge and set the face back off the eaves so the dormer reads as subordinate. Mere contains MERE, STOURTON, ZEALS conservation areas (MERE designated 1973), so materials, fenestration and roof form are assessed against the appraisal, so the cheeks, the window line and the material are drawn to answer it rather than invite a query.
Where Mere's streets are protected — MERE, STOURTON and ZEALS among them — the Class B dormer right is switched off and even a modest rear box needs consent. Wiltshire Council has 48 recorded Article 4 directions, removing permitted development for rear and side extensions and other roof alterations, including rooflights — check the address before assuming PD applies in Mere. We confirm the designation before the box is sized.
Many rear dormers in Mere are permitted development, but the volume and position decide it. You will normally need a full application to Wiltshire Council if any of these apply:
We draw the box within its volume allowance, the flat roof below the ridge and the face set back off the eaves — the three things a dormer stands or falls on — and submit a validation-complete pack, whether that is a lawful development certificate or a full householder application.
Below is Wiltshire Council's real householder decision record, drawn from official planning statistics and refreshed as new data lands. Wiltshire Council granted 96% of its householder applications in the year to 31 March 2026, and MERE shapes what is approved here. A dormer is decided on volume and set-back, so a pack that shows the calculation and the eaves detail is cleared faster and refused less often than a DIY submission.
Source: MHCLG planning application statistics (householder decisions, England, 1 April 2025 - 31 March 2026). Compare every borough on our London approval-rate league table.
Tell us about your project and get a fixed, no-obligation quote back within one working day. If you don't need planning permission at all, we'll tell you that too — for free.
Across MERE, STOURTON and ZEALS, the dormer that goes through is the subordinate rear box: flat roof kept low, cheeks clad to recede, side windows obscure-glazed against overlooking, and the whole thing set back so the original eaves line still reads from the garden. On steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building, this returns a full-height double and en-suite from what was standing-room-only, usually inside the permitted-development volume.
The 2,370 homes here are 33% pre-1900, 11% 1993-1999, 10% 1965-1972, which is what sets the realistic roof and rear-projection options. We keep the box off the ridge, match the cheek material to the roof, and where the volume is already spent — or the street is designated — draw the dormer as a householder application composed to Wiltshire Council's roof-alteration guidance rather than push a certificate that would be refused.
We draw rear dormers on the terraced and semi-detached streets across the borough. A few of the neighbourhoods where Mere dormers come up most often:
Dormer loft drawings for MERE's conservation area designated in 1973 — volume-checked, set-back-detailed and drawn to Wiltshire Council's guidance.
Dormer loft drawings for STOURTON's conservation area designated in 1975 — volume-checked, set-back-detailed and drawn to Wiltshire Council's guidance.
Dormer loft drawings for ZEALS's conservation area designated in 1986 — volume-checked, set-back-detailed and drawn to Wiltshire Council's guidance.
Dormer loft drawings for Kilmington's civil parish within Mere — volume-checked, set-back-detailed and drawn to Wiltshire Council's guidance.
Dormer loft drawings for West Knoyle's civil parish within Mere — volume-checked, set-back-detailed and drawn to Wiltshire Council's guidance.
Dormer loft drawings for Zeals's civil parish within Mere — volume-checked, set-back-detailed and drawn to Wiltshire Council's guidance.
Whether a dormer in Mere needs permission comes down to where it sits and how big the box is. This is how the cases compare.
| Dormer type | Permitted development? | What it gains | What Wiltshire Council checks |
|---|---|---|---|
| Rear box, within volume | Usually yes | Full-height room across the back | Volume total, 20cm eaves set-back |
| Rear box, over volume limit | No — full application | A larger room | How far over the allowance, bulk |
| Front or side dormer | No — full application | Light to the front rooms | Visibility from the street, character |
| Dormer in a conservation area | No — full application | Same space, extra scrutiny | Roof form and street appearance |
In conservation areas such as MERE and STOURTON, Class B dormer rights are removed and every dormer needs a full application.
A fixed process built around how Wiltshire Council validates and decides dormer applications — most drawings are submission-ready within seven days of survey.
Send us your Mere postcode and roof type. We confirm your conservation and Article 4 status, work out how much permitted-development volume you have left, and score your odds against live Wiltshire Council decisions.
We measure ridge and eaves heights, roof pitch and the existing loft floor — the numbers the volume calculation, the set-back and the head heights depend on.
Chartered designers develop the box to your brief, drawn inside the Class B volume limits or, where those are exhausted or removed, to Wiltshire Council's roof-alteration guidance.
We submit the certificate or application, manage validation and case-officer queries, and revise the drawings free until Wiltshire Council issues its decision.
Often not. A rear box dormer within 40 cubic metres on a terrace, or 50 on a semi or detached house, set back at least 20 centimetres from the eaves and kept below the ridge, is usually permitted development. In Mere you will need a full application to Wiltshire Council for a front or side dormer, a box that exceeds the volume, and any dormer in a conservation area such as MERE and STOURTON, where those rights are removed.
The permitted-development limit is a volume, not a footprint: 40 cubic metres of added roof space on a terraced house and 50 on a semi-detached or detached one, and any earlier loft enlargement counts against that total. In Mere the box must also sit below the ridge and back from the eaves. We measure your roof and calculate the exact volume you have left before drawing. Wiltshire Council is the decision-maker.
Not under permitted development. A dormer on the front roof slope, or one facing a highway, always needs a full application to Wiltshire Council, because it changes how the house reads from the street. Rear box dormers are far more likely to be approved — or to be permitted development outright — which is why almost every Mere dormer we draw sits on the back slope.
Often, on a terrace or semi. If the dormer or the loft steelwork meets the party wall with your neighbour, the Party Wall etc. Act applies and notice must be served before work starts — separately from Wiltshire Council's planning decision. We flag the party-wall junction on the drawings so a surveyor can be appointed early and the build is not held up. This applies to your Mere address specifically.
If your dormer is permitted development, a lawful development certificate from Wiltshire Council is council-stamped proof of it — worth holding, because a buyer's solicitor will ask for it when you sell. We prepare and submit the certificate with the same measured drawing pack that shows the box within its volume allowance. This applies to your Mere address specifically.
We price each Mere dormer individually, because the roof pitch and the volume left vary house to house, and send a fixed, no-obligation quote within one working day. It covers the full drawing pack with free revisions until Wiltshire Council approves, and we confirm at the outset whether your box is permitted development or needs an application. Call 020 7864 7245 to start.
Answer five quick questions and get a free planning score for your exact address — instantly. Then, if you want the full picture, unlock the detailed analysis: your council's live approval rates, local precedents, constraints on your street and a step-by-step route to permission.
Same fixed quotes, same fast drawings — wherever your project is.