Rear dormer drawings for Felsted & Stebbing roofs — the box across the back slope that turns a low attic into a full-height room, drawn to Uttlesford District Council's guidance and the volume limits, delivered in days and revised free until your decision, with a free approval-odds check first.
Uttlesford District Council granted 82% of the householder planning decisions it made in its latest published year — 5 points below the 87% England-wide householder average. Felsted & Stebbing contains Felsted, Stebbing conservation areas (Felsted designated 2013), so materials, fenestration and roof form are assessed against the appraisal, which is where a policy-literate drawing pack earns its keep. Its dominant Victorian (1837–1901) and postwar (1945–1970) housing stock sets the design brief on most streets.
Under Class B, a rear dormer stays permitted development up to 40m³ of added roof volume on a terrace or 50m³ on a semi-detached or detached house, while Class A allows a single-storey rear extension of 3m beyond the original rear wall on a terrace and 4m on a detached house before a full application is needed. Felsted & Stebbing carries at least one Article 4 direction, and conservation areas including Felsted and Stebbing remove those rights outright, so we confirm your exact address before a line is drawn. A validated householder application in Felsted & Stebbing is determined against an 8-week statutory target.
Felsted (conservation area designated in 2013), Stebbing (conservation area designated in 2011), Felsted (civil parish within Felsted & Stebbing) and Stebbing (civil parish within Felsted & Stebbing) — these are the Felsted & Stebbing pockets our drawings cover most. Heritage designations here include Felsted and Stebbing. Uttlesford District Council weighs each proposal against Uttlesford District Council's development plan and the design policies it applies to householder applications, where the 2,360 homes here are 21% pre-1900, 9% 1945-1954, 9% 1955-1964, which is what sets the realistic roof and rear-projection options. On roofs the borough is steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and simple gabled and hipped roofs typical of early postwar building, over Victorian and earlier houses (21% of 2,360 homes), early postwar houses (9%) and late-1950s and early-1960s houses (9%).
Felsted & Stebbing's designated heritage is specific, and it is the first thing we check against your address: Felsted (conservation area designated in 2013) and Stebbing (conservation area designated in 2011). Inside those boundaries permitted development is curtailed and Uttlesford District Council assesses materials, window detail and roof form against the area's own appraisal, so a scheme that would be waved through two streets away can need a full application here.
Beyond the designated areas, Felsted & Stebbing takes in Felsted and Stebbing. Uttlesford District Council has 18 recorded Article 4 directions — check the address before assuming PD applies in Felsted & Stebbing.
On stock, Felsted & Stebbing is Victorian and earlier houses (21% of 2,360 homes), early postwar houses (9%) and late-1950s and early-1960s houses (9%) — which is why steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and simple gabled and hipped roofs typical of early postwar building govern what a loft or rear projection can realistically be. Uttlesford District Council decided 535 householder applications in the latest published year and granted 82%, with 82% issued inside the eight-week target. Those are the numbers our drawings are prepared against.
The full build-period split for Felsted & Stebbing runs pre-1900 21% (490 homes), 1900-1918 2% (40 homes), 1919-1929 4% (100 homes), 1930-1939 7% (160 homes), 1945-1954 9% (210 homes), 1955-1964 9% (210 homes), 1965-1972 8% (180 homes), 1973-1982 4% (100 homes), 1983-1992 4% (100 homes), 1993-1999 8% (190 homes) and 2000-2008 6% (150 homes). That distribution is why pre-1900 detailing dominates the drawings here, and it is measured from council-tax records rather than assumed from the street name.
Uttlesford District Council also decides for Elsenham & Henham, Newport, Saffron Walden Audley, Saffron Walden Shire, Stansted North, Takeley, The Sampfords and Great Dunmow North, so a decision in Felsted & Stebbing sits inside a wider pattern of decisions we track across the same authority — useful when an officer cites a precedent from the next area over.
The Article 4 directions recorded for this council include 2 Bentfield End Causeway Stansted, 5 Wicken Road Newport, Addresses at Gilbey Green Belmont Hill and High Street Newport and Broom Wood Cambridge Road Ugley. Each removes a specific permitted-development right inside its own boundary, which is why the check is done on the address rather than on the town.
Published figures for Felsted & Stebbing and Uttlesford District Council. These are the numbers that decide what is realistic on your street, so we work from them rather than from national averages.
| Measure | Felsted & Stebbing |
|---|---|
| Dwellings recorded | 2,360 |
| Built pre-1900 | 490 (21%) |
| Built 1900-1918 | 40 (2%) |
| Built 1919-1929 | 100 (4%) |
| Built 1930-1939 | 160 (7%) |
| Built 1945-1954 | 210 (9%) |
| Built 1955-1964 | 210 (9%) |
| Built 1965-1972 | 180 (8%) |
| Built 1973-1982 | 100 (4%) |
| Built 1983-1992 | 100 (4%) |
| Built 1993-1999 | 190 (8%) |
| Built 2000-2008 | 150 (6%) |
| Built before 1919 | 22% |
| Built 1919–1939 | 11% |
| Built 1945–2008 | 48% |
| Conservation areas in Felsted & Stebbing | 2 (Felsted, Stebbing) |
| Conservation areas district-wide | 42 |
| Article 4 directions recorded | 18 |
| Householder applications decided | 535 |
| Householder applications granted | 82% |
| Decided within 8 weeks | 82% |
Dwelling stock from VOA council-tax data at 31 March 2025; conservation-area and Article 4 counts from planning.data.gov.uk (MHCLG); decision figures are Uttlesford District Council's own, from MHCLG live table PS2 for the year to 31 March 2026.
The box dormer is the workhorse loft, and most of Felsted & Stebbing is built for it — the borough runs to Victorian and earlier houses (21% of 2,360 homes), early postwar houses (9%) and late-1950s and early-1960s houses (9%) under steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and simple gabled and hipped roofs typical of early postwar building, and a flat-roofed box across the rear slope is the cheapest cubic metre of full-height space those roofs give up. Uttlesford District Council tests the dormer against Uttlesford District Council's development plan and the design policies it applies to householder applications, and because permitted development turns on a number, the volume you propose against the volume you have left is the first thing an officer or a certificate checks.
That is why the arithmetic goes on the drawings. We calculate the box against the 40- or 50-cubic-metre allowance, count any earlier roof enlargement into the total, hold the flat roof below the ridge and set the face back off the eaves so the dormer reads as subordinate. Felsted & Stebbing contains Felsted, Stebbing conservation areas (Felsted designated 2013), so materials, fenestration and roof form are assessed against the appraisal, so the cheeks, the window line and the material are drawn to answer it rather than invite a query.
Where Felsted & Stebbing's streets are protected — Felsted and Stebbing among them — the Class B dormer right is switched off and even a modest rear box needs consent. Uttlesford District Council has 18 recorded Article 4 directions — check the address before assuming PD applies in Felsted & Stebbing. We confirm the designation before the box is sized.
Many rear dormers in Felsted & Stebbing are permitted development, but the volume and position decide it. You will normally need a full application to Uttlesford District Council if any of these apply:
We draw the box within its volume allowance, the flat roof below the ridge and the face set back off the eaves — the three things a dormer stands or falls on — and submit a validation-complete pack, whether that is a lawful development certificate or a full householder application.
Below is Uttlesford District Council's real householder decision record, drawn from official planning statistics and refreshed as new data lands. Uttlesford District Council granted 82% of its householder applications in the year to 31 March 2026, and Felsted shapes what is approved here. A dormer is decided on volume and set-back, so a pack that shows the calculation and the eaves detail is cleared faster and refused less often than a DIY submission.
Source: MHCLG planning application statistics (householder decisions, England, 1 April 2025 - 31 March 2026). Compare every borough on our London approval-rate league table.
Tell us about your project and get a fixed, no-obligation quote back within one working day. If you don't need planning permission at all, we'll tell you that too — for free.
Across Felsted, Stebbing and Felsted, the dormer that goes through is the subordinate rear box: flat roof kept low, cheeks clad to recede, side windows obscure-glazed against overlooking, and the whole thing set back so the original eaves line still reads from the garden. On steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building, this returns a full-height double and en-suite from what was standing-room-only, usually inside the permitted-development volume.
The 2,360 homes here are 21% pre-1900, 9% 1945-1954, 9% 1955-1964, which is what sets the realistic roof and rear-projection options. We keep the box off the ridge, match the cheek material to the roof, and where the volume is already spent — or the street is designated — draw the dormer as a householder application composed to Uttlesford District Council's roof-alteration guidance rather than push a certificate that would be refused.
We draw rear dormers on the terraced and semi-detached streets across the borough. A few of the neighbourhoods where Felsted & Stebbing dormers come up most often:
Dormer loft drawings for Felsted's conservation area designated in 2013 — volume-checked, set-back-detailed and drawn to Uttlesford District Council's guidance.
Dormer loft drawings for Stebbing's conservation area designated in 2011 — volume-checked, set-back-detailed and drawn to Uttlesford District Council's guidance.
Dormer loft drawings for Felsted's civil parish within Felsted & Stebbing — volume-checked, set-back-detailed and drawn to Uttlesford District Council's guidance.
Dormer loft drawings for Stebbing's civil parish within Felsted & Stebbing — volume-checked, set-back-detailed and drawn to Uttlesford District Council's guidance.
Whether a dormer in Felsted & Stebbing needs permission comes down to where it sits and how big the box is. This is how the cases compare.
| Dormer type | Permitted development? | What it gains | What Uttlesford District Council checks |
|---|---|---|---|
| Rear box, within volume | Usually yes | Full-height room across the back | Volume total, 20cm eaves set-back |
| Rear box, over volume limit | No — full application | A larger room | How far over the allowance, bulk |
| Front or side dormer | No — full application | Light to the front rooms | Visibility from the street, character |
| Dormer in a conservation area | No — full application | Same space, extra scrutiny | Roof form and street appearance |
In conservation areas such as Felsted and Stebbing, Class B dormer rights are removed and every dormer needs a full application.
A fixed process built around how Uttlesford District Council validates and decides dormer applications — most drawings are submission-ready within seven days of survey.
Send us your Felsted & Stebbing postcode and roof type. We confirm your conservation and Article 4 status, work out how much permitted-development volume you have left, and score your odds against live Uttlesford District Council decisions.
We measure ridge and eaves heights, roof pitch and the existing loft floor — the numbers the volume calculation, the set-back and the head heights depend on.
Chartered designers develop the box to your brief, drawn inside the Class B volume limits or, where those are exhausted or removed, to Uttlesford District Council's roof-alteration guidance.
We submit the certificate or application, manage validation and case-officer queries, and revise the drawings free until Uttlesford District Council issues its decision.
Often not. A rear box dormer within 40 cubic metres on a terrace, or 50 on a semi or detached house, set back at least 20 centimetres from the eaves and kept below the ridge, is usually permitted development. In Felsted & Stebbing you will need a full application to Uttlesford District Council for a front or side dormer, a box that exceeds the volume, and any dormer in a conservation area such as Felsted and Stebbing, where those rights are removed.
The permitted-development limit is a volume, not a footprint: 40 cubic metres of added roof space on a terraced house and 50 on a semi-detached or detached one, and any earlier loft enlargement counts against that total. In Felsted & Stebbing the box must also sit below the ridge and back from the eaves. We measure your roof and calculate the exact volume you have left before drawing. Uttlesford District Council is the decision-maker.
Not under permitted development. A dormer on the front roof slope, or one facing a highway, always needs a full application to Uttlesford District Council, because it changes how the house reads from the street. Rear box dormers are far more likely to be approved — or to be permitted development outright — which is why almost every Felsted & Stebbing dormer we draw sits on the back slope.
Often, on a terrace or semi. If the dormer or the loft steelwork meets the party wall with your neighbour, the Party Wall etc. Act applies and notice must be served before work starts — separately from Uttlesford District Council's planning decision. We flag the party-wall junction on the drawings so a surveyor can be appointed early and the build is not held up. This applies to your Felsted & Stebbing address specifically.
If your dormer is permitted development, a lawful development certificate from Uttlesford District Council is council-stamped proof of it — worth holding, because a buyer's solicitor will ask for it when you sell. We prepare and submit the certificate with the same measured drawing pack that shows the box within its volume allowance. This applies to your Felsted & Stebbing address specifically.
We price each Felsted & Stebbing dormer individually, because the roof pitch and the volume left vary house to house, and send a fixed, no-obligation quote within one working day. It covers the full drawing pack with free revisions until Uttlesford District Council approves, and we confirm at the outset whether your box is permitted development or needs an application. Call 020 7864 7245 to start.
Answer five quick questions and get a free planning score for your exact address — instantly. Then, if you want the full picture, unlock the detailed analysis: your council's live approval rates, local precedents, constraints on your street and a step-by-step route to permission.
Same fixed quotes, same fast drawings — wherever your project is.