Rear dormer drawings for Brigg & Wolds roofs — the box across the back slope that turns a low attic into a full-height room, drawn to North Lincolnshire Council's guidance and the volume limits, delivered in days and revised free until your decision, with a free approval-odds check first.
North Lincolnshire Council granted 91% of the householder planning decisions it made in its latest published year — 4 points above the 87% England-wide householder average. Brigg & Wolds contains Brigg Conservation area, Saxby All Saints Conservation area conservation areas (Brigg Conservation area designated 1971), so materials, fenestration and roof form are assessed against the appraisal, which is where a policy-literate drawing pack earns its keep. Its dominant Victorian (1837–1901) housing stock sets the design brief on most streets.
The permitted-development ceilings are fixed: 40m³ of new roof volume for a terraced loft and 50m³ for a semi or detached house under Class B, plus a 3m single-storey rear extension on a terrace or 4m on a detached house under Class A. Brigg & Wolds carries at least one Article 4 direction, and conservation areas including Brigg Conservation area and Saxby All Saints Conservation area remove those rights outright, so we confirm your exact address before a line is drawn. A validated householder application in Brigg & Wolds is determined against an 8-week statutory target.
Brigg (conservation area designated in 1971), Saxby All Saints (conservation area designated in 1977), Barnetby le Wold (civil parish within Brigg & Wolds), Bonby (civil parish within Brigg & Wolds), Brigg (civil parish within Brigg & Wolds), Cadney (civil parish within Brigg & Wolds), Elsham (civil parish within Brigg & Wolds) and Horkstow (civil parish within Brigg & Wolds) — these are the Brigg & Wolds pockets our drawings cover most. Heritage designations here include Brigg Conservation area and Saxby All Saints Conservation area. North Lincolnshire Council weighs each proposal against North Lincolnshire Council's development plan and the design policies it applies to householder applications, where the 5,560 homes here are 18% pre-1900, 11% 1973-1982, 10% 2000-2008, which is what sets the realistic roof and rear-projection options. On roofs the borough is steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and shallow trussed roofs typical of 1970s building, over Victorian and earlier houses (18% of 5,560 homes), 1970s and early-1980s houses (11%) and 2000s houses and apartments (10%).
Before anything is drawn we check your address against the designations that apply in Brigg & Wolds: Brigg (conservation area designated in 1971) and Saxby All Saints (conservation area designated in 1977). Inside those boundaries permitted development is curtailed and North Lincolnshire Council assesses materials, window detail and roof form against the area's own appraisal, so a scheme that would be waved through two streets away can need a full application here.
Beyond the designated areas, Brigg & Wolds takes in Barnetby le Wold, Bonby, Brigg, Cadney, Elsham and Horkstow. North Lincolnshire Council has 12 recorded Article 4 directions, removing permitted development for rear and side extensions and roof enlargements such as dormers — check the address before assuming PD applies in Brigg & Wolds.
On stock, Brigg & Wolds is Victorian and earlier houses (18% of 5,560 homes), 1970s and early-1980s houses (11%) and 2000s houses and apartments (10%) — which is why steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and shallow trussed roofs typical of 1970s building govern what a loft or rear projection can realistically be. North Lincolnshire Council decided 338 householder applications in the latest published year and granted 91%, with 70% issued inside the eight-week target. That decision record, not a national figure, is what we design to.
The full build-period split for Brigg & Wolds runs pre-1900 18% (1,020 homes), 1900-1918 3% (170 homes), 1919-1929 6% (310 homes), 1930-1939 7% (400 homes), 1945-1954 6% (320 homes), 1955-1964 9% (510 homes), 1965-1972 8% (460 homes), 1973-1982 11% (590 homes), 1983-1992 6% (330 homes), 1993-1999 5% (290 homes) and 2000-2008 10% (570 homes). That distribution is why pre-1900 detailing dominates the drawings here, and it is measured from council-tax records rather than assumed from the street name.
North Lincolnshire Council also decides for Axholme Central, Axholme North, Broughton & Scawby, Ferry and Ridge, so a decision in Brigg & Wolds sits inside a wider pattern of decisions we track across the same authority — useful when an officer cites a precedent from the next area over.
The Article 4 directions recorded for this council include Alkborough & Walcot, Appleby, Barrow upon Humber and Barton upon Humber. Each removes a specific permitted-development right inside its own boundary, which is why the check is done on the address rather than on the town.
Published figures for Brigg & Wolds and North Lincolnshire Council. These are the numbers that decide what is realistic on your street, so we work from them rather than from national averages.
| Measure | Brigg & Wolds |
|---|---|
| Dwellings recorded | 5,560 |
| Built pre-1900 | 1,020 (18%) |
| Built 1900-1918 | 170 (3%) |
| Built 1919-1929 | 310 (6%) |
| Built 1930-1939 | 400 (7%) |
| Built 1945-1954 | 320 (6%) |
| Built 1955-1964 | 510 (9%) |
| Built 1965-1972 | 460 (8%) |
| Built 1973-1982 | 590 (11%) |
| Built 1983-1992 | 330 (6%) |
| Built 1993-1999 | 290 (5%) |
| Built 2000-2008 | 570 (10%) |
| Built before 1919 | 21% |
| Built 1919–1939 | 13% |
| Built 1945–2008 | 55% |
| Conservation areas in Brigg & Wolds | 2 (Brigg Conservation area, Saxby All Saints Conservation area) |
| Conservation areas district-wide | 17 |
| Article 4 directions recorded | 12 |
| Householder applications decided | 338 |
| Householder applications granted | 91% |
| Decided within 8 weeks | 70% |
Dwelling stock from VOA council-tax data at 31 March 2025; conservation-area and Article 4 counts from planning.data.gov.uk (MHCLG); decision figures are North Lincolnshire Council's own, from MHCLG live table PS2 for the year to 31 March 2026.
The box dormer is the workhorse loft, and most of Brigg & Wolds is built for it — the borough runs to Victorian and earlier houses (18% of 5,560 homes), 1970s and early-1980s houses (11%) and 2000s houses and apartments (10%) under steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building and shallow trussed roofs typical of 1970s building, and a flat-roofed box across the rear slope is the cheapest cubic metre of full-height space those roofs give up. North Lincolnshire Council tests the dormer against North Lincolnshire Council's development plan and the design policies it applies to householder applications, and because permitted development turns on a number, the volume you propose against the volume you have left is the first thing an officer or a certificate checks.
That is why the arithmetic goes on the drawings. We calculate the box against the 40- or 50-cubic-metre allowance, count any earlier roof enlargement into the total, hold the flat roof below the ridge and set the face back off the eaves so the dormer reads as subordinate. Brigg & Wolds contains Brigg Conservation area, Saxby All Saints Conservation area conservation areas (Brigg Conservation area designated 1971), so materials, fenestration and roof form are assessed against the appraisal, so the cheeks, the window line and the material are drawn to answer it rather than invite a query.
Where Brigg & Wolds's streets are protected — Brigg Conservation area and Saxby All Saints Conservation area among them — the Class B dormer right is switched off and even a modest rear box needs consent. North Lincolnshire Council has 12 recorded Article 4 directions, removing permitted development for rear and side extensions and roof enlargements such as dormers — check the address before assuming PD applies in Brigg & Wolds. We confirm the designation before the box is sized.
Many rear dormers in Brigg & Wolds are permitted development, but the volume and position decide it. You will normally need a full application to North Lincolnshire Council if any of these apply:
We draw the box within its volume allowance, the flat roof below the ridge and the face set back off the eaves — the three things a dormer stands or falls on — and submit a validation-complete pack, whether that is a lawful development certificate or a full householder application.
Below is North Lincolnshire Council's real householder decision record, drawn from official planning statistics and refreshed as new data lands. North Lincolnshire Council granted 91% of its householder applications in the year to 31 March 2026, and Brigg Conservation area shapes what is approved here. A dormer is decided on volume and set-back, so a pack that shows the calculation and the eaves detail is cleared faster and refused less often than a DIY submission.
Source: MHCLG planning application statistics (householder decisions, England, 1 April 2025 - 31 March 2026). Compare every borough on our London approval-rate league table.
Tell us about your project and get a fixed, no-obligation quote back within one working day. If you don't need planning permission at all, we'll tell you that too — for free.
Across Brigg, Saxby All Saints and Barnetby le Wold, the dormer that goes through is the subordinate rear box: flat roof kept low, cheeks clad to recede, side windows obscure-glazed against overlooking, and the whole thing set back so the original eaves line still reads from the garden. On steeply pitched slate roofs, valley gutters and party parapets typical of pre-1900 building, this returns a full-height double and en-suite from what was standing-room-only, usually inside the permitted-development volume.
The 5,560 homes here are 18% pre-1900, 11% 1973-1982, 10% 2000-2008, which is what sets the realistic roof and rear-projection options. We keep the box off the ridge, match the cheek material to the roof, and where the volume is already spent — or the street is designated — draw the dormer as a householder application composed to North Lincolnshire Council's roof-alteration guidance rather than push a certificate that would be refused.
We draw rear dormers on the terraced and semi-detached streets across the borough. A few of the neighbourhoods where Brigg & Wolds dormers come up most often:
Dormer loft drawings for Brigg's conservation area designated in 1971 — volume-checked, set-back-detailed and drawn to North Lincolnshire Council's guidance.
Dormer loft drawings for Saxby All Saints's conservation area designated in 1977 — volume-checked, set-back-detailed and drawn to North Lincolnshire Council's guidance.
Dormer loft drawings for Barnetby le Wold's civil parish within Brigg & Wolds — volume-checked, set-back-detailed and drawn to North Lincolnshire Council's guidance.
Dormer loft drawings for Bonby's civil parish within Brigg & Wolds — volume-checked, set-back-detailed and drawn to North Lincolnshire Council's guidance.
Dormer loft drawings for Brigg's civil parish within Brigg & Wolds — volume-checked, set-back-detailed and drawn to North Lincolnshire Council's guidance.
Dormer loft drawings for Cadney's civil parish within Brigg & Wolds — volume-checked, set-back-detailed and drawn to North Lincolnshire Council's guidance.
Whether a dormer in Brigg & Wolds needs permission comes down to where it sits and how big the box is. This is how the cases compare.
| Dormer type | Permitted development? | What it gains | What North Lincolnshire Council checks |
|---|---|---|---|
| Rear box, within volume | Usually yes | Full-height room across the back | Volume total, 20cm eaves set-back |
| Rear box, over volume limit | No — full application | A larger room | How far over the allowance, bulk |
| Front or side dormer | No — full application | Light to the front rooms | Visibility from the street, character |
| Dormer in a conservation area | No — full application | Same space, extra scrutiny | Roof form and street appearance |
In conservation areas such as Brigg Conservation area and Saxby All Saints Conservation area, Class B dormer rights are removed and every dormer needs a full application.
A fixed process built around how North Lincolnshire Council validates and decides dormer applications — most drawings are submission-ready within seven days of survey.
Send us your Brigg & Wolds postcode and roof type. We confirm your conservation and Article 4 status, work out how much permitted-development volume you have left, and score your odds against live North Lincolnshire Council decisions.
We measure ridge and eaves heights, roof pitch and the existing loft floor — the numbers the volume calculation, the set-back and the head heights depend on.
Chartered designers develop the box to your brief, drawn inside the Class B volume limits or, where those are exhausted or removed, to North Lincolnshire Council's roof-alteration guidance.
We submit the certificate or application, manage validation and case-officer queries, and revise the drawings free until North Lincolnshire Council issues its decision.
Often not. A rear box dormer within 40 cubic metres on a terrace, or 50 on a semi or detached house, set back at least 20 centimetres from the eaves and kept below the ridge, is usually permitted development. In Brigg & Wolds you will need a full application to North Lincolnshire Council for a front or side dormer, a box that exceeds the volume, and any dormer in a conservation area such as Brigg Conservation area and Saxby All Saints Conservation area, where those rights are removed.
The permitted-development limit is a volume, not a footprint: 40 cubic metres of added roof space on a terraced house and 50 on a semi-detached or detached one, and any earlier loft enlargement counts against that total. In Brigg & Wolds the box must also sit below the ridge and back from the eaves. We measure your roof and calculate the exact volume you have left before drawing. North Lincolnshire Council is the decision-maker.
Not under permitted development. A dormer on the front roof slope, or one facing a highway, always needs a full application to North Lincolnshire Council, because it changes how the house reads from the street. Rear box dormers are far more likely to be approved — or to be permitted development outright — which is why almost every Brigg & Wolds dormer we draw sits on the back slope.
Often, on a terrace or semi. If the dormer or the loft steelwork meets the party wall with your neighbour, the Party Wall etc. Act applies and notice must be served before work starts — separately from North Lincolnshire Council's planning decision. We flag the party-wall junction on the drawings so a surveyor can be appointed early and the build is not held up. This applies to your Brigg & Wolds address specifically.
If your dormer is permitted development, a lawful development certificate from North Lincolnshire Council is council-stamped proof of it — worth holding, because a buyer's solicitor will ask for it when you sell. We prepare and submit the certificate with the same measured drawing pack that shows the box within its volume allowance. This applies to your Brigg & Wolds address specifically.
We price each Brigg & Wolds dormer individually, because the roof pitch and the volume left vary house to house, and send a fixed, no-obligation quote within one working day. It covers the full drawing pack with free revisions until North Lincolnshire Council approves, and we confirm at the outset whether your box is permitted development or needs an application. Call 020 7864 7245 to start.
Answer five quick questions and get a free planning score for your exact address — instantly. Then, if you want the full picture, unlock the detailed analysis: your council's live approval rates, local precedents, constraints on your street and a step-by-step route to permission.
Same fixed quotes, same fast drawings — wherever your project is.